15
APP-001f
SEPT 2016
SECTION 3 COMPONENT DESCRIPTIONS
DISPLAY MESSAGES
O
Startup Delay Mode – appears for 10 minutes a4er
APPT evaporator shell temperature reads below 40F
(4C) and the foul gas pressure is higher than 80 PSIG
(5.5 BARG).
O
System IniJalizing – appears a4er either the System
Reset key has been pressed or power is cycled to the
APPT while the Liquid Make-Up Level Sensor is
reading wet. APPT will stay in this mode un>l Liquid
make-Up Level Sensor goes dry. This prevents the
heaters from turning on un>l the evaporator shell has
filled with liquid.
O
Releasing Air – appears when the APPT is releasing
noncondensible gas.
O
CollecJng Air/Water – appears when the APPT is in
its normal opera>ng of collec>ng noncondensible gas
and water.
DISPLAY MESSAGES
O
Startup Delay Mode – appears for 10 minutes a4er
APPT evaporator shell temperature reads below 40F
(4C) and the foul gas pressure is higher than 80 PSIG
(5.5 BARG).
O
System IniJalizing – appears a4er either the System
Reset key has been pressed or power is cycled to the
APPT while the Liquid Make-Up Level Sensor is
reading wet. APPT will stay in this mode un>l Liquid
make-Up Level Sensor goes dry. This prevents the
heaters from turning on un>l the evaporator shell has
filled with liquid.
O
Releasing Air – appears when the APPT is releasing
noncondensible gas.
O
CollecJng Air/Water – appears when the APPT is in
its normal opera>ng of collec>ng noncondensible gas
and water.
DISPLAY MESSAGES
O
Startup Delay Mode – appears for 10 minutes a4er
APPT evaporator shell temperature reads below 40F
(4C) and the foul gas pressure is higher than 80 PSIG
(5.5 BARG).
O
System IniJalizing – appears a4er either the System
Reset key has been pressed or power is cycled to the
APPT while the Liquid Make-Up Level Sensor is
reading wet. APPT will stay in this mode un>l Liquid
make-Up Level Sensor goes dry. This prevents the
heaters from turning on un>l the evaporator shell has
filled with liquid.
O
Releasing Air – appears when the APPT is releasing
noncondensible gas.
O
CollecJng Air/Water – appears when the APPT is in
its normal opera>ng of collec>ng noncondensible gas
and water.
DISPLAY MESSAGES
O
Startup Delay Mode – appears for 10 minutes a4er
APPT evaporator shell temperature reads below 40F
(4C) and the foul gas pressure is higher than 80 PSIG
(5.5 BARG).
O
System IniJalizing – appears a4er either the System
Reset key has been pressed or power is cycled to the
APPT while the Liquid Make-Up Level Sensor is
reading wet. APPT will stay in this mode un>l Liquid
make-Up Level Sensor goes dry. This prevents the
heaters from turning on un>l the evaporator shell has
filled with liquid.
O
Releasing Air – appears when the APPT is releasing
noncondensible gas.
O
CollecJng Air/Water – appears when the APPT is in
its normal opera>ng of collec>ng noncondensible gas
and water.
Startup Delay Mode
– appears for 10 minutes after APPT
evaporator shell temperature reads below 40F (4C) and
the foul gas pressure is higher than 80 PSIG (5.5 BARG).
System Initializing
– appears after either the System
Reset key has been pressed or power is cycled to the
APPT while the Liquid Make-Up Level Sensor is reading
wet. APPT will stay in this mode until Liquid make-Up
Level Sensor reads dry. This prevents the heaters from
turning on until the evaporator shell has filled with liquid.
Collecting Air/Water
– appears when the APPT is in
its normal operating of collecting noncondensible gas
and water.
Releasing Air
– appears when the APPT is releasing
noncondensible gas.
DISPLAY MESSAGES FOR APPT
