Hans Grohe Axor Shower Select 36712000 Скачать руководство пользователя страница 4

Страница: 4 / 44

Assembly see page 34

Fault

Cause

Remedy

Insufficient water

Supply pressure inadequate

Check water pressure (If a pump has been installed
check to see if the pump is working).

Regulator filter dirty

Clean filter in front of the mixer and on the MTC-
thermo cartridge

Shower filter seal dirty

Clean filter seal between shower and hose

Crossflow, hot water being forced into cold water pipe,
or vice versa, when mixer is closed

Backflow preventers dirty or leaking

Clean backflow preventers, exchange if necessary

Spout temperature does not correspond with tempera-
ture set

Thermostat has not been adjusted

Adjust thermostat

Hot water temperature too low

Increase hot water temperature to 42 ºC to 65 ºC

Temperature regulation not possible

Temperature regulator dirty or calcified

Clean temperature regulator, exchange if necessary

Safety stop button not operating

Spring defective

Clean spring and/or button, exchange if necessary

Button calcified

Valve stiff

Select stop valve DN9 damaged

Exchange Select stop valve DN9

Shower or spout dripping

Select stop valve DN9 damaged

Exchange Select stop valve DN9

Pushbutton cannot be actuated or is without function

Safety guard of isolating valve has not been removed

Remove safety guard from isolating valve

Pushbutton is jammed or stiff

Seal needs greasing

Grease the seal

Pushbutton does not snap in

Select Adapter incorrectly trimmed

Trim and mount Select Adapter according to Fig. 7
(see page 34)

First, fully press the pushbutton down into the rosette;
then, mount the rosette

Test certificate

(see page 44)

Cleaning

(see enclosed brochure)

Dimensions

(see page 31)

Spare parts

(see page 42)

Colors

000 = chrome plated

610 = black

Maintenance

(see page 40)

• The mixer is equipped with check valves. The check valves must be

checked regularly according to DIN EN 1717 in accordance with
national or regional regulations (at least once a year).

• To guarantee the smooth running of the thermostat, it is necessary

from time to time to turn the thermostat from total hot to total cold.

Operation

(see page 39)

Minor leaking may occur briefly during initial commissioning and inter-
ruption/restart of the water supply.

Adjustment

(see page 38)

After the installation, the output temperature of the thermostat must be
checked. A correction is necessary if the temperature measured at the
output differs from the temperature set on the thermostat.

Safety Function

(see page 38)

The desired maximum temperature for example max. 42º C can be pre-
set thanks to the safety function.

Installation example

(see page 32)

Do not use silicone containing acetic acid!

Symbol description

English

Safety Notes

Gloves should be worn during installation to prevent crushing and cutting
injuries.

The product may only be used for bathing, hygienic and body cleaning pur-
poses.

Children as well as adults with physical, mental and/or sensoric impairments
must not use this product without proper supervision. Persons under the influ-
ence of alcohol or drugs are prohibited from using this product.

The hot and cold supplies must be of equal pressures.

Installation Instructions

• Prior to installation, inspect the product for transport damages. After it has been

installed, no transport or surface damage will be honoured.

• The pipes and the fixture must be installed, flushed and tested as per the applica-

ble standards.

• The plumbing codes applicable in the respective countries must be observed.

Special information for UK

If installing this product with a pump, please be aware that it has to have negative
head switching. This product will not function with a positive head pump..

Technical Data

Operating pressure:

max. 1 MPa

Recommended operating pressure:

0,1 - 0,5 MPa

Test pressure:

1,6 MPa

(1 MPa = 10 bar = 147 PSI)
Hot water temperature:

max. 70°C

Recommended hot water temp.:

65°C

Thermal disinfection: