background image

In selecting a site-choose a sunny level position away from overhanging trees.

If you are fixing your Aluminum Greenhouse directly to a solid concrete foundation use the

This is a multi-part assembly, allow at least 3-4 hours for assembly.

Do not lean against or push the Aluminum Greenhouse during construction.

Do not attempt to assemble this Aluminum greenhouse if you are tired ,have taken drugs or

Do not position your Aluminum greenhouse in an area exposed to excessive wind.

Do not attempt to assemble the Aluminum greenhouse in windy or wet conditions,

The Aluminum greenhouse must be positioned and fixed on a flat level surface.

Aluminum greenhouse needs cleaning, use a mild detergent solution and rinse

clear panels.

  

Hot items such as recently used grills, blowtorches etc.must not be stored in the Wall shed.

Keep children away from the assembly area.

!

     SAFETY ADVICE

We strongly recommend the use of work gloves during assembly.

Do not touch overhead power cables with the aluminum profiles.

Always wear shoes and safety goggles when working with extruded aluminum.

 alcohol or if you are prone to dizzy spells.

If using a step ladder or power tools ensure that you follow the manufactures safety advice.

Ensure there are no hidden pipes or cables in the ground before inserting the pegs.

Dispose of all plastic bags safely and keep them out of reach of children.

Note that the door is hinged on the right hand side and therefore opens to the right space needed.

    GENERAL ADVICE

pre drilled holes in the metal base supplied.

The component parts should be checked and laid out close at hand.

Keep all small parts(screws etc)in a bowl so they do not get lost.

Keep roof clear of snow and leaves.

with cold clean water.

  

CARE & MAINTENANCE

When your 

Do NOT use acetone, abrasive cleaners or other special detergents to clean the

Содержание 9820101-1





















Отзывы: