background image

 

INSTALLATION INSTRUCTIONS 

Before Using your Ice Maker 

 

Remove the exterior and interior packing. 

 

Before connecting the ice maker to the power source, let it stand upright for approximately 2 hours. This 
will reduce the possibility of a malfunction in the cooling system from handling during transportation. 

 

Clean the interior surface using a soft cloth and a lukewarm  mixture of 2 tablespoons of baking soda for 
each quart of lukewarm water.. 

 

This appliance is intended to be used for residential applications. 

 

When disposing your appliance, please choose an authorized disposal site. 

 

Installation of your ice maker 

 

This appliance is designed to be for free standing or built-in installation . 

 

Place your ice maker on a level surface that is strong enough to support the weight when fully loaded.  

 

This  appliance  is  using  flammable  refrigerant.  Be  careful  not  to  damage  the  cooling  pipe  during  the 
transportation.  

 

Place the ice maker away from direct sunlight and sources of heat (stove, heater, radiator, etc.).  

 

Direct  sunlight  may  affect  the  acrylic  coating  and  heat  sources  may  increase  electrical  consumption. 
Extreme cold ambient temperatures may also cause the unit not to perform properly. 

 

Avoid locating the unit in humid areas.  

 

Plug the ice maker into a properly installed-grounded wall outlet. Do not under any circumstances cut or 
remove the third (ground) prong from the power cord. Any questions concerning power and/or grounding 
please contact a certified electrician or an authorized product service center. 

CAUTION 

 

To store the ice maker cooler for an extended period of time; the unit should have a thorough cleaning and 
the door should be left ajar to allow air to circulate. This will avoid possible formations of condensation, 
mold or odors.

 

 

Ambient Room Temperature Limits 

This appliance is designed to operate in ambient temperatures specified by its temperature class marked on the 
rating plate. 
 

Class 

Symbol 

Ambient Temperatures range(°

F

Extended Temperate 

SN 

50 to 

90 

Temperate 

60 to 

90 

Subtropical 

ST 

60 to 

100 

Tropical 

60 to 

109 

 

Содержание 9760701






















Отзывы: