CONNECTING THE UNIT TO POWER
Plug one end of the AC adaptor into the DC power Input, and then plug the other end into AC wall outlet.
Before switching on the unit, make sure that the voltage of your electricity supply is the same as that
indicated on the rating plate.
BATTERY BACKUP
Insert two pieces UM-4 batteries into the battery compartment. Be sure to observe the proper polarity (the
"+" and "-" signs) as indicated inside the battery compartment.
In case of power failure or interrupted AC power, the current time and alarm time settings, the stored radio
stations are preserved in the memory of the unit by means of battery back-up function.
SETTING THE CLOCK
1. When the unit is OFF ( Clock mode ), press and hold the
CLK/MEM
button for about 1 second, the time
will begin to flash on the LED display.
2. Press the
HOUR/
/ button to adjust the hour.
3. Press the
MIN/
button to adjust the minute.
4. When the correct time is selected, press the
CLK/MEM
button again to confirm.
SETTING THE ALARMS
1. When the unit is OFF, press the
AL1/VOL+
or
AL2/VOL−
button. The ALARM time will begin to flash on
the LED display.
2. Press the
HOUR/
button to adjust the alarm hour.
3. Press the
MIN/
button to adjust the alarm minute.
4. When the correct time is selected, press the
AL1/VOL+
or
AL2/VOL−
button to confirm.
5. Press the
AL1/VOL+
or
AL2/VOL−
button to select the ALARM sound mode -
BUZZER
or currently set
RADIO
station. The alarm buzzer or radio indicator will light up.
SNOOZE FUNCTION
1. Whenever the alarm (radio or buzzer) activates, it can be temporarily suspended for a short period of 9
minutes by pressing the
SNOOZE/SLEEP
button once.
2. The buzzer or radio will then automatically activate again after the 9 minutes SNOOZE period has ended.
3. This procedure can be repeated for up to approximately one hour.
TURN OFF THE ALARM
When the Alarm activate, press the
/SOURCE/AL.OFF
button to turn off the Alarm.
PROJECTION
1. Press the
PROJECTION ON/OFF
button to turn on the
PROJECTION
function.
2. The projector displays the time via a bright red projection light onto a wall, ceiling or any surface for
viewing in a darkened room.
3. Rotate the Projector wheel to point the Projector lens to the desired direction. The projector lens can
vertically swivel 180° so that you may view the TIME from different position. .
4. If the projected image is out of focus, use the
PROJECTION FOCUS
knob to adjust the image until the
projection is in focus.
5. To turn off the PROJECTION function, press the
PROJECTION ON/OFF
button again.
Notes
1. Do not stare into the lens directly.
2. The projector function cannot be used unless the clock has been set.
3. Certain walls and ceilings may not display the projection properly.
4. Don’t rotate the projector wheel beyond its limits, it may be damaged.
-3-
LISTENING TO THE FM RADIO
1. Press the
/SOURCE/AL.OFF
button to select
FM radio
mode.
2. Press the
HOUR/
button or
MIN/
button step by step to tune to the desired radio stations.
3. Press and hold the
HOUR/
button or
MIN/
buttons for approx. 1 second, it will start to search the
next radio station in the direction of the search. The search operation simply finds stations with strong
signals. Stations with weak reception can only be tuned in manually.
ANTENNA
For best reception, fully extend the FM wire antenna to receive FM stations.
SAVING A RADIO STATION TO THE MEMORY
1. Tune the radio to the desired station.
2. Press and hold the
CLK/MEM
button for approx. 1 second, the LED display will show
P01
and flash, the
radio station will stored in the memory.
3. Up to 10 FM radio stations can be stored in the memory.
TO LISTEN TO A SAVED RADIO STATION
1. Press th
e
/SOURCE/AL.OFF
button to select
FM radio
mode
2. Press the
CLK/MEM
button to select the stored radio station.
SLEEP TO MUSIC FUNCTION
1. This function allows you to listen to the radio while you fall asleep.
2. Press the
SNOOZE/SLEEP
button, the display will show the default sleep time of 90 minutes
3. Press the
SNOOZE/SLEEP
button again to adjust the desired sleep time.
4. The options are 90-80-70-60-50-40-30-20-10-min. or OFF
5. Now you can enjoy listening to the radio for the pre-set period of sleep time.
6. After this pre-set time has elapsed, the unit will switch off automatically.
AUX IN CONNECTION
1. Insert one side of the audio cable (requires 3.5mm stereo plug, not supplied) into the line-out jack or
phones jack on your MP3 player or audio device and the other side to the aux-in jack on the unit.
2. Press the
/SOURCE/AL.OFF
button to select AUX mode,
AUX
will display in the LED display for a few
seconds.
3. Turn on your MP3 player and follow the playback instruction.
4. To stop this function, simply turned off your MP3 player.
CHARGE YOUR DEVICES (2.4A and 1A)
Connect the standard size end of a USB cable (not included) to the USB ports on the unit and connect the
other end to the charging port of your devices. The unit contains two USB ports (2.4A and 1A).
Remarks:
Some devices may not support USB charging or
may require a higher power rating than this product provides.
Observe the charging status on your device. Ensure your
device is working properly before attempting to charge.
Charging function may not be supported for all phones or
electronic devices
-4-
