OPERATIONAL GUIDE
BATTERY REPLACEMENT
Battery replacement must only take place in a safe area and
using a 9V alkaline battery.
Simply slide off the battery cover on the back of the meter,
detach the battery from the terminals and attach a new 9V
battery, while paying attention to the correct polarity. Replace
the battery cover.
ACCESSORIES
IST99556 09/18
Before using this product, make sure it is entirely suitable for
your specific application and for the environment in which it
is used. Any variation introduced by the user to the supplied
equipment may degrade the meters’ performance. For yours and
the meter’s safety do not use or store the meter in hazardous
environments.
EMISSIVITY
The instruments measure the temperature of objects with an
emissivity of 0.95, which is the characteristic of most substances,
such as organic material, water, plastic, fabrics, etc.
To measure substances that have a polished surface and are
very reflective, the emissivity needs to be compensated. It is
advisable to cover the object with black paint or black adhesive
tape to compensate for the reflectivity.
WARNING
To avoid damage, do not hold the sensor too close to a heat
source for a long period.
SENSOR CLEANING
To maintain the instrument’s accuracy, it is important that the
sensor lens is kept clean. To clean the sensor, gently wipe the
lens with a humid and non-abrasive cloth (
HI731318
).
EXTERNAL PROBE (HI99556 only)
Connect the
HI765PW
temperature
probe to the connector on top of the
instrument.
MEASUREMENT MODE
Press the IR/CONTACT button to select the external probe
measurement mode: “P” appears on the LCD to indicate that
the mode has been entered.
Dip the probe in the substance which to be measured (an
immersion level of approximately 4 cm is recommended), and
wait for the reading to stabilize.
LOW BATTERY
These instruments continuously check the battery status. If the
battery level is too low to ensure realiable reading, the meter
shuts off the LCD completely. In this case and if the meter can
not be switched on, it is recommended to replace the battery
immediately.
WARRANTY
HI99551
and
HI99556
are warranted for two years against
defects in workmanship and materials when used for its intended
purpose and maintained according to instructions. Probes are
guaranteed for a period of six months.
This warranty is limited to repair or replacement free of
charge. Damages due to accident, misuse, tampering or lack of
prescribed maintenance are not covered. If service is required,
contact your local Hanna Instruments Office. If under warranty,
report the model number, date of purchase, serial number and
the nature of the failure. If the repair is not covered by the
warranty, you will be notified of the charges incurred. If the
instrument is to be returned to Hanna Instruments, first obtain a
Returned Goods Authorization Number from the Customer Service
department and then send it with shipment costs prepaid.
When shipping any instrument, make sure it is properly pack-
aged for complete protection.
INFRARED SENSOR MEASUREMENT
Switch the instrument on.
For
HI99556
models, check that the
instrument is in IR (infrared) mode.
If necessary (a “P” tag appears on the LCD to indicate “external
probe mode”), press the IR/CONTACT button to switch to IR
(infrared) measurement mode.
To measure the temperature
of an object, simply aim the
sensor in the direction of the
object.
READING DISTANCE
The distance between the sensor and the object is an important
factor in infrared measurement.
The relation between “distance/object area” is 3:1. This means
that the diameter of the measured area is one third of the
distance between the sensor and the object.
For example, if the sensor is 15 cm away from the object,
the instrument measures the temperature of an area with a
5 cm diameter.
HI710007
Blue shockproof rubber boot
HI710008
Orange shockproof rubber boot
HI731318
Wiping tissue (4 pcs.)
HI765PW
Penetration thermistor probe with white handle
RECOMMENDATIONS FOR USERS
All rights are reserved. Reproduction in whole or in part is
prohibited without the written consent of the copyright owner.
