manualshive.com logo in svg

Hanna Instruments HI97106, Инструкция по эксплуатации, Страница: 26 / 28

Поделиться
Скачать
Hanna Instruments HI97106 Скачать руководство пользователя страница 26

Battery Replacement 

26

Tutorial mode has been enabled in the Setup menu. 
Press 

Continue

 and follow the prompt on the screen. Tutorial mode can be 

disabled in the Setup menu.

The log is full (200 logs). New logs will replace the oldest. Displays before a new 
log would overwrite the oldest record. Press 

Continue

 to accept.

A critical error has occurred. Restart the meter. 
If the issue persists, please contact Hanna Instruments

®

 technical support.

9.  BATTERY REPLACEMENT

To replace the instrument’s batteries:

1.  Press and hold the 

 key to turn the instrument off.

2.  Remove the battery cover by turning it counterclockwise.
3.  Remove the old batteries and replace with three new 1.5V AA batteries.
4.  Replace the battery cover and turn it clockwise to close.

10.  ABBREVIATIONS

EPA

US Environmental Protection Agency

HR

High Range

LR

Low Range

MR

Medium Range

UHR

Ultra High Range

NIST

National Institute of Standards and Technology

Содержание HI97106





























Отзывы:

Нет отзывов