manualshive.com logo in svg

Hanna Instruments HI 8931, Инструкция по эксплуатации

Поделиться
Скачать
Hanna Instruments HI 8931 Скачать руководство пользователя страница 34

34

• Pour at least 8 cm (3¼") of conductivity

solution into a plastic beaker.

• Immerse the probe into the conductivity

solution. The holes on the sleeve must be
completely submerged in the solution.

• Tap the probe repeatedly on the bottom of the beaker and stir it to

ensure that no air bubbles remain trapped inside the sleeve.

• If the temperature of the probe is close to that of the solution, the

display of 

HI 8931

 will stabilize quickly and provide a temperature

compensated conductivity measurement. Allow a few minutes if there
is a temperature difference of about 5°C (9°F) or more for the ATC
circuitry to compensate completely.

•

For HI8936

Adjust the SLOPE trimmer of the 

HI 8936 

transmitter to read on the

ammeter:
"10.4 mA" using 

HI 7034

 and 

HI 8936 A/AL

"14.304 mA" using 

HI 7030

 and 

HI 8936 B/BL

"15.304 mA" using 

HI 7031

 and 

HI 8936 C/CL

"10.72 mA" using 

HI 7033 

and 

HI 8936 D/DL

Содержание HI 8931

















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды