Hanna Instruments HI 8510 Скачать руководство пользователя страница 40

Страница: 40 / 70

OPERATIONAL GUIDE

The setting of the various keys are made via
the front panel keys and trimmers. When
each key is pressed the LED is lighted indi-
cating to the user that the function is in
operation.

Make sure that the pH or the ORP meter
with the electrode is calibrated before operat-
ing the instruments (see page 40-42).

SET POINTS

HI 8710, HI 8720, HI 931500 and HI 932500 only

To set the working point of pH or ORP dos-
age, press the "SET" key. The display will
show the set value.

Use a small screwdriver to adjust the trim-
mers "COARSE" and "FINE" until the de-
sired set value is displayed.

HI 8711 and HI 931501 only

To set the working point of acid dosage,
press the "ACID SET" key. The display will
show the set value for acid dosage.

COARSE

ACID SET

FINE

ACID

SET

BASE

SET

COARSE

SET

FINE

SET

COARSE

SET

FINE

SET

Содержание HI 8510







































































Результаты поиска

Содержание HI 8510

Отзывы:

Бренды по названию

Популярные бренды

Hanna Instruments HI 8510, Инструкция по эксплуатации

Результаты поиска

Содержание HI 8510

Отзывы:

Бренды по названию

Популярные бренды