Hanna Instruments HI 504901, Инструкция по эксплуатации, Страница: 21 / 35

41 40
When all information can not be sent with one SMS (the
maximum number of characters for an SMS is 160), it will be
sent more than one message, each one beginning with the
label “Info#p/#t:” which gives the indication of the progres-
sive information SMS number (#p) and the total number of
information SMSs (#t) that are going to be sent for the cur-
rent instrument.
Find here below a complete list of available information (and
coded notations) for all devices which can communicate with
the
HI504901 interface.
Information SMSs for HI8001 and HI8002 controllers
For these meters the <INFORMATION SPECIFIC TO THE
INSTRUMENT> field reports the following information:
• “Ctrl: INIT or STOP or WORK or BLOCK or CHECK or
HALTED”: work status of the controller, which can be ini-
tialization or stop or work or block or tech-check or sys-
tem-halted;
• “Alarm: ON or OFF”: indicates if there is at least one
active alarm in the system;
• “Anom: ##”: anomalies total number;
• “pHn: ##.#”: indicated values by pH sensors (1 and 2);
• “ECn: ##.#”: indicated values by conductivity sensors
(1, 2 and 3);
• “SR: ####”: indicated value by solar radiation sensor;
• “IrPRG: ##”: number of the active irrigation program; if
no irrigation program is active, then this indication will be
“IrPG:--”;
• “P#: NOT or SET or RDY or ACT or FIN or WAIT or DEL”:
status of all irrigation programs (10), which can be not set
or set or ready or active or finished or waiting or delayed;
• “C#: NOT or SET or RDY or ACT or FIN or WAIT or DEL”:
status of cleaning filter programs (2), which can be not set
or set or ready or active or finished or waiting or delayed;
• “Pump: ON or OFF or BLK”: status of pumps, which can
be on or off or block;
• “CondStop”: conditional stoppage input, if active;
• “TmpBrk”: temporary break input, if active.
All these information will be reported in two SMSs; if some alarm
is active in
HI8001 or HI8002 controller, a third SMS will be
sent, with the label “INFO3/3”. This message will contain the
got from the controlled instruments, and could be requested,
for example, after an alarm message regarding an error which
should close without any intervention. The user could also want
to be informed about the values of the measured magnitudes
or current devices status.
The information messages can be requested:
1. by making a call from one of the phone numbers programmed
for alarm messages sending: in this case the cellular phone
interface recognizes the calling phone number, hangs up
without answering and then sends to the calling number
one (or more) information message(s) for each controlled
instrument;
2. by sending an SMS from whatever cellular phone to the
device. The message must have the following format:
“P<CELLULAR PHONE INTERFACE PASSWORD>”, i.e.
the uppercase P letter followed by the cellular phone inter-
face password in uppercase letters; if the password is
disabled, just “P” is enough. Upon this requesting mes-
sage, the interface will send one (or more) information
message(s) for each controlled instrument to the cellular
phone which issued the requesting SMS.
The format of the information messages is very similar to the
one for alarm messages. The only difference is the “Info:
<INFORMATION SPECIFIC TO THE INSTRUMENT>” string
instead of “Alarms: <ALARM SPECIFIC TO THE INSTRU-
MENT>” (see previous subsection for details).
The format of information messages for the instruments con-
nected to the RS232 ports will be:
“<INSTRUMENT NAME>; RS232-<NUMBER OF THE
RS232 CHANNEL>; Info: <INFORMATION SPECIFIC TO
THE INSTRUMENT>; Rem msg: <NUMBER OF REMAIN-
ING MESSAGES>”
while of information messages for the instruments connected
to the RS485 ports will be:
“<INSTRUMENT NAME>; RS485-<RS485 DEVICE AD-
DRESS>; Info: <INFORMATION SPECIFIC TO THE INSTRU-
MENT>; Rem msg: <NUMBER OF REMAINING MES-
SAGES>”.
For <INSTRUMENT NAME> and <NUMBER OF REMAIN-
ING MESSAGES> fields, please refer to the previous sub-
section.