Hankscraft Runxin RevV4 Скачать руководство пользователя страница 49

Страница: 49 / 57

RevV4 Valves & Systems Service Manual

Hankscraft Runxin, LLC 300 Wengel Drive 608.524.9465 hrh2o.com [email protected]

Electronics

Problem

Cause

Correction

1. Abnormal

display

A. Wiring to the front panel is loose.

B. Control board is faulty.

C. Transformer malfunction.

D. Electrical service unstable.

A. Check and replace the wiring.

B. Replace control board.

C. Check and replace transformer.

D. Verify power source.

2. Blank display

A. Wiring to the front panel is loose.

B. Front panel damaged.

C. Control board damaged.

D. Electricity is interrupted.

A. Check and replace wiring.

B. Replace front panel.

C. Replace control board.

D. Check power source.

3. E1 code

A. Wiring of locating board with controller

fails to work.

B. Locating board damaged.

C. Mechanical drive failure.

D. Faulty control board.

E. Wiring to the motor has a short.

F. Motor damaged.

A. Replace wiring.

B. Replace locating board.

C. Replace Discs or drive gear.

D. Replace control board.

E. Replace wiring.

F. Replace motor.

4. E2 code

A. Hall effect on locating board damaged.

B. Possible short in the wiring to the locating

board.

C. Control board malfunction.

A. Replace locating board.

B. Replace wiring.

C. Replace control board.

5. E3 or E4 code

A. Control board malfunction.

A. Replace control board.

Содержание RevV4


























































Результаты поиска

Содержание RevV4

Отзывы:

Похожие инструкции для RevV4

Бренды по названию

Популярные бренды

Hankscraft Runxin RevV4, Руководство по обслуживанию

Результаты поиска

Содержание RevV4

Отзывы:

Похожие инструкции для RevV4

Бренды по названию

Популярные бренды