Hanil M15R Скачать руководство пользователя страница 20

Страница: 20 / 24

www.ihanil.com

20/22

6.2 Error Codes

6. Troubleshooting

Code

Message

Cause

Recommended Action

Imbalance

error

• Asymmetrical arrangement of

tubes.

• Different volume of sample .

• Check the tightness of rotor loading.

• Check the proper loading of tubes.

• Check the stable ground or

worktable.

Over speed error

• 2% over the set RPM.

• Check controller and motor.

• Switch power on/off and re-start.

Motor

over-heat

• Temp. hike inside of motor.

• Check the stator of motor.

• Switch power off, restart after 1 hour.

Motor error

• Motor operation error

• Switch power on/off and re-start.

Door open (Operating)

• Lid open during operation

• Contact the Technical support team.

System error

• System error

• Contact the Technical support team.

E10

Inner Temperature Over

OR Inner

temperature sensor error

• Occurs when the set

temperature is not reached

• Inner temperature sensor error

• Make sure there is enough space

around the ventilation slots.

• Switch power on/off and re-start.

E11

Motor

tempterature

sensor error !

• Motor temperature sensor

error

• Switch power on/off and re-start.

E12

HI voltage

Error

• High voltage

• Switch power on/off and re-start.

E13

Low voltage Error

• Low voltage

• Switch power on/off and re-start.

E15

RPM sensing error

• RPM Sensor error

• Rotor identification error

• Switch power on/off and re-start.

E16

Compressor

tempterature

sensor error !

• Compressor

tempterature sensor error

• Switch power on/off and re-start.

E17

Communi-

cation error

• Occurs when Main and IO

board are disconnected

• Switch the device off and contact

the Technical support team.

Содержание M15R

























Результаты поиска

Содержание M15R

Отзывы:

Похожие инструкции для M15R

Бренды по названию

Популярные бренды

Hanil M15R, Руководство по эксплуатации

Результаты поиска

Содержание M15R

Отзывы:

Похожие инструкции для M15R

Бренды по названию

Популярные бренды