H&S GM 170 Скачать руководство пользователя страница 35 | Manualshive

Страница: 35 / 86

background image

SERVICE

-33-

HYDRAULIC SYSTEM

Hydraulic Pump Sheave Alignment

The hydraulic pump drive and driven sheaves must be maintained in correct alignment and be tightly
secured at all times.

Hydraulic Pump Belt Tension

Overload protection for the hydraulic pump is provided by a self-adjusting spring tightener that

requires

no adjustment. The idler pulley must be properly positioned to keep the belt aligned with the sheaves.

Cyclonic Hydraulic Reservoir

The oil filter should be replaced once a year or every 75 hours of operation, whichever comes first.
The oil should be drained and replaced every two years or every 150 hours of operation, whichever
comes first. Keep oil filled to proper level.

MILL/BLOWER DRIVE

Belt Replacement

To replace the mill/blower drive belt, perform the following steps:

1. Disengauge PTO, shut-off tractor and remove key.

2. Release front drive chain tension.

3. Loosen both of the bolt/nut (A & B) assemblies on the main

drive shaft.

5. After tension is released, remove the old belt and replace

with a new Belt.

6. Adjust the new belt tension per the Adjustment Chapter of

this manual. After tension is properly adjusted, re-connect
the front drive chain idler bracket spring.

IMPORTANT:

The mill/blower drive belt will deteriorate more rapidly if improper tension is applied. Uneven

sheave alignment will result in uneven belt stretch. Improper mill/blower belt tension will produce excessive
pressure on the mill/blower bearings and cause premature bearing failure.

A

B

«
...
33
34
35
36
37
...
»

Содержание GM 170























































































Отзывы:

Нет отзывов

Похожие инструкции для GM 170

Бренд: Pall Страницы: 51

Бренд: ZAMST Страницы: 21

Бренд: Landoll Страницы: 6

Бренд: ParaBody Страницы: 9

Бренд: ParaBody Страницы: 3

Бренд: MacDon Страницы: 45

Бренд: H&S Страницы: 30

Бренд: UFO Страницы: 16

Бренд: Tascam Страницы: 80

Бренд: Tascam Страницы: 2

Бренд: Walker Страницы: 24

Бренд: jcb Страницы: 41

Бренд: Latham Страницы: 4

Бренд: SafeWaze Страницы: 23

Бренд: natus Страницы: 20

Dantec Keypoint G4

Бренд: natus Страницы: 42

Бренд: natus Страницы: 149

LED Street Bar 16x3W RGB IP65

Бренд: Varytec Страницы: 9

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды