![background image](http://html1.mh-extra.com/html/hands/forage-box/forage-box_operators-manual_3103408031.webp)
-29-
LUBRICATION
GENERAL INFORMATION
IMPORTANT:
Catch and dispose of fluid per local waste disposal regulations whenever service is performed
on hydraulic components, valves, cylinders, hoses, etc.
GEARBOXES
Main Apron Drive Gearbox: Keep the main apron gearbox filled to the oil level plug in cover of gearbox
using 85W140 lubricant.
Beater Drive Gearbox: Keep the beater drive gearbox filled to the center of the shafts. Use 80w-90 lubricant.
DRIVE CHAINS
Lubricate the drive chains with a light machine oil. Keep chains aligned with sprockets; this lengthens the
life of the sprockets and chain. Lubricate chains often.
GREASING
There are numerous grease fittings on the Forage Box. Become familiar with all lubrication points and
establish a routine to ensure complete lubrication of the Forage Box. Lubricating properly and often (every
10 hours) with a high-quality grease will prolong the life of the forage box. Replace any missing or plugged
grease fittings. Wipe dirt from the fittings before greasing to prevent the dirt from being forced into the
bearing or pivot. Grease should come out around the shaft on sleeve-type bearings. On the sealed ball
bearings, grease should be added slowly until a slight bead forms at the seal indicating the correct amount
of lubricant. To minimize dirt build-up, avoid excessive greasing. After greasing, wipe off the excess grease
from around the outside of the bearings to prevent the accumulation of chaff and grit.
1. (1) one on beater drive clutch.
2. (1) one on beater drive sprocket.
3. (1) one on beater engage bronze yoke.
4. (2) one at each end of brace - gearbox to main apron drive shaft.
5. (2) remote fittings for right hand and center main apron drive shaft bushings.
6. (5) remote fitting - beater bearing (3 right side 2 left side) ( sealed bearings - DO NOT over-grease).
7. (1) one on left hand main apron drive shaft bushing. (access through discharge opening)
8. (4) one on each main apron rear idler sprocket. (4 front unload) (8) front and rear unload)
9. (1) one on drive shaft end of brace for rear main apron drive shaft.
10. (1) one on gear reduction sprocket at rear of forage box.
11. (3) one on left, center and right hand rear drive shaft brackets.
12. (1) bottom beater left hand bearing.
13. (2) remote fittings for optional 4th beater.
Содержание FORAGE BOX
