Hand Held Products Quick Check 200 Series Скачать руководство пользователя страница 53 | Manualshive

Страница: 53 / 72

background image

47

Switch Position Function

Down Left

Off

Center

On

Down Right

Paper Feed

A red light-emitting diode (LED) to the right of the power switch lights to indicate
to On and Paper Feed states.

The printer has a VAC wall-outlet-mounted transformer with an 8-foot cord. The
power transformer cord has a transformer on one end and has a mating
connector to the printer on the other end.

An interface cable connects the printer directly to the Quick Check to provide
easy exchange of scanning results. The connectors on each end of the cable are
keyed so that they cannot be plugged in the wrong way.

Setup the QCP or QCHSP:

1.

Place the printer on a hard, flat surface such as a table or desktop.

2.

Press the power switch into the Off (down left) position.

3.

Plug the power connector from the transformer into the printer.

4.

Plug the transformer into a wall outlet.

Install or replace the QCP or QCHSP paper roll:

1. Press the printer power switch to the Off (down left) position.
2. Remove the printer cover by locating the four small grooves embossed on

each side of the printer cover and tilting the cover open by pushing down
gently on both sets of these grooves.

3. If necessary, remove the empty roll. Press and hold the power switch in the

Paper Feed (down right) position to advance the paper about one inch
beyond the paper cutter.

Warning: Do not pull paper out of the back of the printer. This will damage the
mechanism.

«
...
51
52
53
54
55
...
»

Содержание Quick Check 200 Series









































































Отзывы:

Нет отзывов

Похожие инструкции для Quick Check 200 Series

Бренд: Sunpak Страницы: 8

Бренд: Syris Страницы: 5

Бренд: Symbol Страницы: 12

DS6707-SR20007ZZR

Бренд: Symbol Страницы: 2

Бренд: Metrologic Страницы: 66

Бренд: Fcar Страницы: 12

Z800 - Workstation - 6 GB RAM

Бренд: HP Страницы: 9

Бренд: Winlong Industrial Страницы: 11

Tiris 2000 Series

Бренд: Texas Instruments Страницы: 46

Бренд: Graphic Products Страницы: 56

Бренд: Nordic ID Страницы: 4

Бренд: malata Страницы: 15

EZ6000 Plus Series

Бренд: Godex Страницы: 8

Бренд: Godex Страницы: 40

Бренд: RTscan Страницы: 21

Бренд: Datalogic Страницы: 2

Бренд: Opticon Страницы: 1

Бренд: Rosslare Страницы: 70

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды