Hand Held Products Quick Check 200 Series Скачать руководство пользователя страница 39 | Manualshive

Страница: 39 / 72

background image

33

7. Special Functions

The Quick Check

®

200 series can be set to a special “static” reflectance

measurement function (Reflectometer Mode). This mode is especially useful in
investigating the underlying optical characteristics of bar code symbols. The
Reflectometer Mode, along with the Command Code mode is covered below.

Reflectometer Mode

This menu selectable Special Function is entered by pressing the Scroll [<>]
Button when [Reflectom’r>] is present on the LCD. Then in this special
reflectometer mode, the reflectance “seen” by the QC200’s optics is continuously
displays as both a two digit reflectance percentage and on a graphic bar graph
as soon as the mode is invoked.

Here the xx% and the graphic bar graph (or “gas gauge”) represent a reflectance
value of 00% to 100% from the static reflectometer. This mode is not
“memorized” when the unit is shut off. When turning the unit back on after power
down, it will be necessary to re-establish the Reflectometer Mode if needed. For
these values to be meaningful and consistent, it is critical first that reflectance
calibration have been performed recently and second that the QC200 be held
with its “reflectance foot” and optics tip both touching the sample to maintain the
proper angle.

Command Code Programming

The Quick Check

®

200 series has the unique ability to be “pre-programmed” by

the user by scanning a specially encoded code 128 symbol. This symbol will
automatically make all the selections normally made by the user stepping
through the normal menu sequence. This is particularly useful if the user has
one or two particular setups that they are constantly switching between.
Samples of Command Codes, such as the Command Code to “reset” the QC200
back to all generic default settings, are included with each unit.

NOTE: Display orientation (Right Handed vs. Left Handed) and Printer Interface
selection ARE NOT set using the Command Code. Factory default settings for
these are “Right handed” and “QCHSP”.

Users with one of the accessory Quick Check

®

Printers can produce a Command

Code of their QC200’s present set-up by following the next steps;

First be sure your Quick Check

®

200 is connected to a Quick Check

®

Printer, that

the proper interface selection has been made and both are turned on. Next,

«
...
37
38
39
40
41
...
»

Содержание Quick Check 200 Series









































































Отзывы:

Нет отзывов

Похожие инструкции для Quick Check 200 Series

Бренд: NCR Страницы: 6

Бренд: Icarus Страницы: 59

Бренд: Obreey Страницы: 71

855-S1610040400

Бренд: ddm hopt+schuler Страницы: 25

Бренд: Obreey Страницы: 54

Бренд: Cognex Страницы: 22

Бренд: Cognex Страницы: 55

Бренд: Code Soft Страницы: 2

Бренд: Code Soft Страницы: 71

Бренд: Schlumberger Страницы: 22

Бренд: Godex Страницы: 29

Бренд: Godex Страницы: 43

IDM140BT Series

Бренд: SICK Страницы: 16

Бренд: SICK Страницы: 30

Бренд: ZKTeco Страницы: 40

Бренд: Datalogic Страницы: 53

Бренд: Diablotek Страницы: 1

JADAK flexpoint HS-1M

Бренд: FujiFilm Страницы: 88

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды