Hand Held Products IMAGETEAM 3800i Скачать руководство пользователя | Manualshive

Страница: 72 / 168

background image

6 - 2

3800i/3800r User’s Guide

Enabling the Secondary Interface

The secondary interface can be programmed at any time.

You can temporarily disable the secondary interface, but still retain the
secondary interface settings in the imager’s memory by scanning the Disable
bar code below. To re-enable the secondary interface, scan the Enable bar
code.

Default =Disable.

Secondary RS-232 Connection

All communication parameters between the scanner and terminal must match for
correct data transfer through the serial port using RS-232 protocol.

RS-232 programmable selections are used by both the primary and secondary
interfaces. Changing an RS-232 parameter (e.g., baud rate or parity), while in
primary

or secondary mode will affect both interfaces. If you want to change the

RS-232 settings, refer to the

Connecting the Scanner with RS-232 Serial Port

section on pages 2-8 to 2-11.

Secondary Code 39 Wand Emulation

In Wand Emulation mode, the scanner decodes the bar code then sends data in
the same format as a wand scanner. The Code 39 Format converts all
symbologies to Code 39. The Same Code Format transmits UPC, EAN, Code
128 and Interleaved 2 of 5 without any changes, but converts all other
symbologies to Code 39. These codes set the transmission rate to 25 inches per
second and the output polarity to black, high.

The

Code 39 Format bar code below sets the terminal ID to 61, and the Same

Code Format bar code sets the terminal ID to 64.

* Disable

Enable

RS-232 Interface

Wand Emulation

Code 39 Format

Wand Emulation

Same Code Format

«
...
70
71
72
73
74
...
»

Содержание IMAGETEAM 3800i









































































































































































Отзывы:

Нет отзывов

Похожие инструкции для IMAGETEAM 3800i

Бренд: Themis Страницы: 2

Бренд: SATO Страницы: 20

Бренд: PSC Страницы: 44

Gryphon I GM440 Series

Бренд: Datalogic Страницы: 350

Бренд: Addonics Technologies Страницы: 1

Бренд: Farpointe Data Страницы: 2

Бренд: Silvercrest Страницы: 58

Бренд: Unitech Страницы: 109

Бренд: Hamlet Страницы: 55

Бренд: Hamlet Страницы: 102

Бренд: Kimaldi Страницы: 30

Бренд: Champtek Страницы: 79

Cipher 1660 BT Portable

Бренд: Dataman Страницы: 9

Бренд: Schlumberger Страницы: 22

Бренд: TagMaster Страницы: 26

Бренд: Datalogic Страницы: 20

Бренд: Datalogic Страницы: 56

Бренд: WiredTime Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды