Hand Held Products IMAGETEAM 3800i Скачать руководство пользователя | Manualshive

Страница: 3 / 168

background image

Statement of Agency Compliance

This device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that
may cause undesired operation.

FCC Class B Compliance Statement

This equipment has been tested and found to comply with the limits for a Class
B digital device pursuant to part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following
measures:

•

Reorient or relocate the receiving antenna.

•

Increase the separation between the equipment and receiver.

•

Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.

•

Consult the dealer or an experienced radio or television technician for
help.

Caution: Any changes or modifications made to this device that are not
expressly approved by Hand Held Products may void the user’s authority to
operate the equipment.

Note: To maintain compliance with FCC Rules and Regulations, cables
connected to this device must be shielded cables, in which the cable shield
wire(s) have been grounded (tied) to the connector shell.

Canadian Notice

This equipment does not exceed the Class B limits for radio noise emissions as
described in the Radio Interference Regulations of the Canadian Department of
Communications.

Le present appareil numerique n’emet pas de bruits radioelectriques depassant
les limites applicables aux appareils numeriques de la classe B prescrites dans
le Reglement sur le brouillage radioelectrique edicte par le ministere des
Communications du Canada.

«
1
2
3
4
5
...
»

Содержание IMAGETEAM 3800i









































































































































































Отзывы:

Нет отзывов

Похожие инструкции для IMAGETEAM 3800i

Бренд: Sunpak Страницы: 8

Бренд: SATO Страницы: 32

Бренд: TSC Страницы: 78

Бренд: I-Rocks Страницы: 4

Бренд: StarTech.com Страницы: 2

Бренд: TSC Страницы: 2

Бренд: Billow Страницы: 95

Бренд: IDTECK Страницы: 20

Бренд: IDTECH Страницы: 19

Бренд: IDTECH Страницы: 23

Бренд: IDENTEC SOLUTIONS Страницы: 55

Бренд: Kimaldi Страницы: 30

FlashLink UCF-100

Бренд: SimpleTech Страницы: 4

Cipher 1660 BT Portable

Бренд: Dataman Страницы: 9

Бренд: Jinmuyu Страницы: 7

Бренд: Datalogic Страницы: 188

Бренд: Datalogic Страницы: 282

Бренд: ARKSCAN Страницы: 67

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды