HAMWORTHY HEATING LTD
1
FLEET V series
500001213/G
1.0 INTRODUCTION
1.1
This boiler must be installed by a competent
person . All installations
MUST
conform to the relevant
Gas Safety and Building Regulations. Health & Safety
requirements must also be taken into account when
installing any equipment. Failure to comply with the
above may lead to prosecution.
1.2
This boiler is intended for use on Group H Natural
Gas (2nd Family) .The firing information is to be found in
Appendix ‘A’. Boilers
MUST NOT
use gas other than
that for which they are designed and adjusted.
1.3
The ‘Fleet’ is a gas fired, fully modulating, pre-mix,
condensing, room sealed central heating / hot water
boiler, comprising of 8 models covering the range of 40 -
150kW output, which can be configured vertically in two
or three high units (V series) upto three units wide.
sharing common water pipework - optional HHL supply.
See figures 3.2.1 - - 3.2.5 , for typical schematic layout.
1.3.1
Using the latest gas / air ratio control technology
it is able to provide clean efficient operation across a
large output range via the Merley Boiler Sequence
Controller, ideally suited to installations that do not have
a dedicated controls installation.
The Merley control provides cascade management for
multiple boilers and simultaneous management of three
different circuits operating at different temperatures.
(radiators, dhw & under-floor heating) .
Operation is initiated and controlled by a LMU boiler
management system with a user interface LCD display
for accessing and changing boiler parameters.
1.3.2
Each of the boiler models is designed for direct
connection to a plastic flue system - HHL supply. The
Technical Data for the various arrangements is given in
Appendix C.
The flue outlets from individual modules are linked by a
vertical flue manifold which may be connected to a
single chimney (not HHL supply) up to a maximum
length refer to Appendix C
No draught diverter is fitted to the boiler nor is a fixed
diverter required in the flue system.
However, for B23 applications, the Hamworthy supplied
air inlet filter MUST be fitted to provide the correct clean
air supply to the boiler. Refer to appendix C.
1.3.3
The Fleet is intended for the heating of
Commercial and Industrial premises, or large residential
properties. It may also be used to supply hot water for
these premises via an indirect cylinder.
1.3.4
The Fleet has a low water content and is fitted with
an integral circulating pump to ensure that water flow
rates are achieved - refer to Appendix E for available
pump head to the system.
Accordingly in a primary circuit - refer Appendix E there
is no need for a primary circulating pump.
1.4
The boiler is suitable for connection to open vented
and un-vented (pressurised) heating system, care must
be taken to ensure all extra safety requirements are
satisfied and that the relevant interlocks will shut the
boiler(s) off should a high or low pressure fault occur.
The pressurisation unit must also incorporate a low level
water switch which protects the water pumps and will
directly or indirectly shut down the boiler plant should a
low water condition occur. Consideration should also be
given to the maximum working pressure of the boiler as
given in Appendix ’E’. Consult Hamworthy Heating
Technical Department for help or assistance if in doubt.
1.5
The Fleet boiler is not suitable for direct connection to
domestic hot water supplies.
1.6 BOILER MODELS
2 or 3 high models
Fleet F40V- 80 or 120. - output 80 or 120kW
Fleet F50V-100 or 150. - output 100 or 150kW
Fleet F60V-120 or 180. - output 120 or 180kW
Fleet F70V-140 or 210. - output 140 or 210kW
Fleet F85V-170 or 255. - output 170 or 255kW
Fleet F100V- 200 or 300. - output 200 or 300kW
Fleet F125V- 250 or 375. -output 250 or 375kW
Fleet F150V - 300 or 450. - output 300 or 450kW
1.7
Each Fleet boiler module is supplied with a vfc
contact output for Normal Run and General Fault outputs,
and 0~10v analogue control input compatibility.
1.8
Options -
refer to individual kit instructions for details
1.8.1
Optional water pipework kits are available for two or
three high vertical units upto three units wide. These kits
are free-standing allowing installation to the system prior
to installing the boiler and incorporate all necessary
valves, inter connecting pipework, and flow and return
headers. Refer to individual kit instructions 500005134 for
details.
1.8.2
Controls peripherals
The LMU boiler management system has the potential to
accept the following control options:
1.8.2.1
External sensor
Allows direct weather compensation for multiple boiler
systems.
1.8.2.2
Clip in module (LPB Bus)
Allows communication with multiple boilers under the
control of a Merley Boiler Sequence Controller
1.8.2.3
Merley Boiler Sequencer Controller
Allows cascade management of up to 16 boilers, and
interface with a BMS system.
Содержание F100V
