background image

8

Attaching the fan to the 
electrical box

 

Loosen the two mounting screws (II) in the outlet box.

 

Pass the 120-Volt supply wires through the center hole in the 
mounting bracket (A).

 

Slide the mounting bracket (A) on to the mounting screws (II) 
and center the mounting bracket (A) in relation to the outlet box. 
If necessary, use leveling washers (not included) between the 
slide-on mounting bracket (A) and the outlet box. The flat side of 
the slide-on mounting bracket (A) should face toward the outlet 
box, as shown.

 

Securely tighten the two mounting screws (II).

1

WARNING:

 To reduce the risk of fire, electric shock 

or personal injury, mount to an outlet box marked 

“Acceptable for fan support of 35 lb (15.9 kg) or less”, 

and use screws provided with the outlet box.

NOTE:

 The mounting bracket (A) is designed to slide 

into place on an outlet box with the outlet box screws 

(II) installed.

Assembly - Standard Ceiling Mount (continued)

Assembling the fan

 

Loosen, but do not remove, the setscrew (KK) on the collar (PP) on 
top of the fan motor assembly (E).

 

Align the holes at the bottom of the ball/downrod assembly (B) 
with the holes in the collar on top of the fan-motor assembly (E). 

 

Carefully insert the hanger pin (CC) through the holes in the collar 
and ball/downrod assembly (B). Be careful not to jam the hanger 
pin (CC) against the wiring inside the ball/downrod assembly (B).

 

Insert the locking pin (DD) through the hole near the end of the 
hanger pin (CC) until it snaps into its locked position. 

 

Re-tighten the setscrew (KK) on the collar (PP) on top of the fan 
motor assembly (E).

WARNING:

  Failure  to  properly  install  the  locking 

pin  (DD)  could  result  in  the  fan  becoming  loose  and 

possibly falling.

CAUTION:

 To ensure wobble-free operation and to avoid 

damage to the fan, the downrod (B) and the setscrew (KK) 

must be completely tightened.

3

Assembly - Hanging the Fan

C

D

E

JJ

B

CC

DD

KK

PP

A

II

II

Содержание LOWRY 52-LOWRY





































Отзывы: