manualshive.com logo in svg

HAMPTON BAY 864-766, Руководство пользователя

Поделиться
Скачать
HAMPTON BAY 864-766 Скачать руководство пользователя страница 13

9.

Figure 13

Outlet box

Hanger
bracket

Canopy

Canopy
cover

Screws

Attaching the Fan Blades

Step 1 

Attach 

blades to the blade arms 

using three screws and rubber washers as 
shown in Figure 14.  Start a screw into the arm, 
do not tighten. Repeat for the 2 remaining 
screws and washers.

Step 2 

Tighten each screw securely starting 

with the center screw. Make sure the blade is 
straight.

the 

Step 3

 Fasten the blade arms to the motor by 

inserting the tab from the blade arms to the slot 
in the bottom motor housing, then tighten the 
two screws and washers already installed in the 
blade arms (Figure 15).

Finishing the Installation

Step 1.

 Tuck connections neatly into ceiling 

outlet box.

Step 2. 

Slide the canopy up to ceiling and over 

the 2 screws on the hanger bracket. Rotate 
canopy clockwise. Next, while holding the 
canopy with one hand, slide the canopy cover 
over the screws and rotate  clockwise until tight. 

Note: 

adjust the canopy screws as necessary 

until the canopy and canopy cover are snug. 
(Fig. 13)

WARNING

Make sure the notch on the hanging bracket 

properly sits in the groove in the hanger 

ball before attaching the canopy to the 

bracket by turning the housing until it 

drops into place.

'

Rubber

washer

Blade
arm

Figure 14

Blade

Screws

Figure 15

Motor

Blade  arm

Slot

Tab

Содержание 864-766




















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды