HAMPTON BAY 460-952 Скачать руководство пользователя страница 10

Страница: 10 / 15

Figure 13

Finishing the Installation

Step 1.

Tuck connections neatly into ceiling

outlet box.

Step 2.

Slide the canopy up to ceiling and over

the 2 screws on the hanger bracket. Rotate
canopy clockwise. Next, while holding the
canopy with one hand, slide the canopy cover
over the screws and rotate clockwise until tight.

Note:

Adjust the canopy screws as necessary

until the canopy and canopy cover are snug.
(Fig. 13)

WARNING

Make sure the notch on the hanging bracket

properly sits in the groove in the hanger ball

before attaching the canopy to the bracket by

turning the housing until it drops into place.

Outlet box

Hanger
bracket

Hanger
ball

Canopy

Canopy
cover

Figure 12

Installation of Safety
Support

n additional safety support is provided to

prevent the fan from falling. Secure the
safety cable to the ceiling joist with screw
and washer, as illustrated in Figure 12.

Safety Cable

Hanger
bracket

Outlet box

Содержание 460-952
















Результаты поиска

Содержание 460-952

Отзывы:

Бренды по названию

Популярные бренды

HAMPTON BAY 460-952, Руководство пользователя

Результаты поиска

Содержание 460-952

Отзывы:

Бренды по названию

Популярные бренды