Hampshire Controls ToSentry Скачать руководство пользователя | Manualshive

Страница: 14 / 22

background image

Hampshire Controls Corp.

Revision 1.2

Temperature Transmitter Operating Instruction

Page 13 of 21

©2014

Alarm Conditions

Temperature Alarms

The  Temperature  Transmitter  has  programmable  low  and  high  temperature  limits  as  well  as  an
alarm delay time which control when the alarm indication is activated.  The alarm conditions are
checked every 3 minutes following each new temperature reading.  Alarm processing is based on
the following flowchart.

The local temperature alarm is indicated by a triple beep from the buzzer and 5 slow red flashes

…

…

…

…

of the LED repeated every 15 seconds.

NOTE: Depending on the configuration of the T°Sentry ALERT System software, alert messages
may be sent before, after, or at the same time (within 3 minutes) as the Temperature Transmitter
local alarm.

«
...
12
13
14
15
16
...
»

Содержание ToSentry























Отзывы:

Нет отзывов

Похожие инструкции для ToSentry

Pacemark PM4410

Бренд: Oki Страницы: 2

Бренд: Cloud Страницы: 5

FIBREDATA Series

Бренд: Televes Страницы: 4

PQRM5100 11 U I Series

Бренд: Datcon Страницы: 80

Бренд: HME Страницы: 13

Бренд: TRUEYES Страницы: 11

Бренд: HBC Страницы: 18

Бренд: RACOM Страницы: 241

Бренд: Aruba Страницы: 12

Бренд: Raymarine Страницы: 58

Бренд: Intek Страницы: 52

Бренд: ARG Страницы: 11

Бренд: KWorld Страницы: 13

Бренд: Icom Страницы: 24

Бренд: Minebea Страницы: 30

Бренд: Genie Страницы: 2

Бренд: Genie Страницы: 2

Бренд: Genie Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды