background image

User Manual 

HRDSL512/HRDSL512P4 

56 

Frequent loss of 

ADSL linesync 

(disconnections). 

Ensure that all other devices connected to the same 

telephone line as your router (e.g. telephones, fax 

machines, analogue modems) have a line filter connected 

between them and the wall socket (unless you are using a 

Central Splitter or Central Filter installed by a qualified and 

licensed electrician), and ensure that all line filters are 

correctly installed and the right way around. Missing line 

filters or line filters installed the wrong way around can 

cause problems with your ADSL connection, including 

causing frequent disconnections. 

 

Problems with the LAN Interface 

Problem 

Corrective Action 

Can’t ping any PCs 

on the LAN. 

Check the Ethernet LEDs on the front panel. The LED 

should be on for a port that has a PC connected. If it is off, 

check the cables between your router and the PC. Make 

sure you have uninstalled any software firewall for 

troubleshooting. 

The Router is not 

visible from the PC 

of the LAN 

Verify that the IP address and the subnet mask are 

consistent between the router and the workstations. 

 
 

Содержание HRDSL512

























































Отзывы: