Hameg HM303-6 Скачать руководство пользователя страница 52

Страница: 52 / 66

Subject to change without notice

C2110/C2107:

10:1 Attenuator compensation CH II

–  Press CH I/II pushbutton (IN position) to select channel II.
–  Set attenuator CH II to 5 mV/div.
–  Set amplitude calibrator to 1kHz and connect a 2:1 pre-

attenuator (HZ23) via 50 Ω cable to input of CH II.

– Set amplitude calibrator output voltage to 50 mV

(25

at the 2:1 pre-attenuator output) terminated with 1MΩ

(oscilloscope input impedance).

– Adjust trimmer in pre-attenuator for a ﬂ at square wave

top.

– This adjustment must not be changed during the following

adjustment.

– Locate and identify trimmers C2110 and C2107 for CH II on

YP-Board.

–  Set input coupling to DC.
–  Set time base to 2 ms/div.
–  Set attenuator CH II to 50 mV/div.
–  Set amplitude calibrator output voltage to 0.5 V

(0.25

at the 2:1 pre-attenuator output) terminated with 1MΩ

(oscilloscope input impedance).

–  Adjust C2110 for a ﬂ at top.
–  Adjust C2107 for a leading edge without overshoot.
–  Repeat C2110 and C2107 adjustment until optimum is ob-

tained.

Do not change the 2:1 (HZ23) pre-attenuator adjustment and
continue with item 24.

2 : 1 overcompensate

2 : 1 undercompensate

2 : 1 correct

C2107 undercompensate

C2110 overcompensate

C2107 overcompensate

C2110 undercompensate

Correct

P2008

P2011 P2012

P2006

P2007

P2005

P2002

P2001

C2007

C2010

C2009

C2011

P2003

C2107

C2108

C2103

C2110

P2016

P2014

P2015

P2010

P2009

YP-Board

A d j u s t m e n t P r o c e d e r e H M 3 0 3 - 6

Содержание HM303-6



































































Результаты поиска

Содержание HM303-6

Отзывы:

Похожие инструкции для HM303-6

Бренды по названию

Популярные бренды

Hameg HM303-6, Руководство по обслуживанию

Результаты поиска

Содержание HM303-6

Отзывы:

Похожие инструкции для HM303-6

Бренды по названию

Популярные бренды