HAMAR LASER A-1519 Series Скачать руководство пользователя страница 28

Страница: 28 / 49

Avg. Mode

•

Normal Running Average of

Samples (Default)

•

Reset Average if Position Change Exceeds STDEV (Standard Deviation)

•

Reset Average if Position Change Exceeds 2*STDEV (2X Standard Deviation)

•

Reset Average if Position Change Exceeds 4*STDEV (4X Standard Deviation)

•

Reset Average if Position Change Exceeds 8*STDEV (8X Standard Deviation)

•

Reset Average if Position Change Exceeds 4

μm (4 M

icrons)

•

Reset Average if Position Change Exceeds 8 μm (8 Microns)

•

Reset Average if Position Change Exceeds 16 μm (16 Microns)

•

Reset Average if Position Change Exceeds 32 μm (32 Microns)

•

Reset Average if Position Change Exceeds 64 μm (64 Microns)

Note:

Reset Position Modes should be used only for very stable environments.

Pos. Sensing

The Unitarget utility is

not

compatible with the Type I (IR or radio) Unitargets. The utility is only

intended for use with Type II A-1519 and A-1520 Unitargets. The Type II Unitargets have a USB and an

AUX port on the left side of the target and a circular connector in the back. The Type I Unitarget is

smaller and only has a single circular connector in the back.

There are two types of Type II Unitargets in the field. The A-1519 targets can be identified by the sensor

type, visible through the front window as shown

in Figure 44.

Type II-Legacy, Single Axis Sensor

•

Compatible with radio version of the

Type I Unitarget.

•

Supports all scanning lasers.

•

Does

not

support fixed (continuous) or

pulsed line lasers.

Type II-Current Version, Dual Axis Sensor

•

Supports all scanning lasers.

•

Supports fixed (continuous) and pulsed

line lasers.

Configure the target using the utility, based on

the laser type and Type II Unitarget as follows:

Scanning, Single Axis Legacy Mode:

Select

this mode for Type II Legacy Targets

only

. Select

for use with scanning lasers only.

Scanning, Dual Axis Mode:

Select this mode

for Type II, current version. Select for use with

scanning lasers only.

Fixed Beam, Dual Axis:

Select this mode for all continuous line lasers (for example the L-700 and L-

705 in continuous mode).

Pulsed Beam, Dual Axis:

Select this mode for use with pulsed line lasers only (for example, the L-705

in pulsed beam mode).

Figure 44 –

A-1519 Single and Dual-Axis Sensors

Содержание A-1519 Series


















































Результаты поиска

Содержание A-1519 Series

Отзывы:

Похожие инструкции для A-1519 Series

Бренды по названию

Популярные бренды

HAMAR LASER A-1519 Series, Руководство по эксплуатации

Результаты поиска

Содержание A-1519 Series

Отзывы:

Похожие инструкции для A-1519 Series

Бренды по названию

Популярные бренды