Hamamatsu ORCA-Flash4.0 LT3 Скачать руководство пользователя страница 3

Страница: 3 / 47

ORCA-Flash4.0 LT3 Digital CMOS camera C11440-42U40 Instruction manual_Ver.1.1

1. SAFETY PRECAUTIONS

1-1 SYMBOLS

The following symbols can be found on this camera:

Direct current

Alternating current

1-2 CLASSIFICATION OF WARNINGS

We have classified the warnings symbols that appear in this instruction manual and on the camera

as follows for your convenience. Make sure that you fully understand them and follow the

instructions they contain.

Improper handling of the camera without observing these warnings

could lead to serious injury to the user and even death.

Improper handling of the camera without observing these cautions

could lead to personal injury to the user or damage to property.

Note

This symbol indicates a note to help you get the best performance from

the camera. Read the contents of the note carefully to ensure correct and

safe use. Failure to observe one of these notes might impair the

performance of the camera.

This symbol indicates a cautionary item that should be followed when

handling the camera. Read the contents carefully to ensure correct and

safe use.

This symbol indicates an action that is forbidden. Read and follow the

instructions carefully.

This symbol indicates a compulsory action or instruction. Read and follow

the instructions carefully.

Содержание ORCA-Flash4.0 LT3
















































Результаты поиска

Содержание ORCA-Flash4.0 LT3

Отзывы:

Похожие инструкции для ORCA-Flash4.0 LT3

Бренды по названию

Популярные бренды

Hamamatsu ORCA-Flash4.0 LT3, Инструкция по эксплуатации

Результаты поиска

Содержание ORCA-Flash4.0 LT3

Отзывы:

Похожие инструкции для ORCA-Flash4.0 LT3

Бренды по названию

Популярные бренды