POWER
MENU
SETUP
SHIFT
PROG+
PROG
VOL+
VOL
OK
EPG
EXIT
SAT
TV
DVD
AV
4
7
1
2
5
8
0
3
6
9
VCR
MODE
DVBT
AUX
CBL
AMP
17
5
6
8
1
2
9
10
3
16
15
4
14
13
7
12
11
2
3
Universal Remote Control
Function buttons
1. LED display
2. Mode key for device selection at the
second level (AUX, AMP, DVB-T, CBL)
3. Device selection buttons(TV/AUX, VCR/
AMP, DVD/DVB-T, SAT/CBL)
4. Setup
5. VOL+/VOL–:Volume control
6. Text ON:Switch on TeletextMenu:Open
device menu
7. Hold:Hold the current Teletext page
8. Number keys 0-9
9. AV:Switch to an external device
10.
E
Rewind / red
B
Play / yellow
F
Fast forward / blue
I
Start recording
Stop / green
J
Pause / magenta
11. -/--: Switch to two-digit channel
numbers
12. Info: Information about the station
(depending on device)
EPG: Display Electronic Programme Guide
(depending on device)
13. Text OFF: Switch off Teletext
EXIT: Exit device menu
14. P+/P–:Programme selection
15.
H
Mute switch
OK: Confirm your entry
16. Shift: For the blue function buttons, e.g.
OK When the Shift button is pressed, the
LED is illuminated. The Shift function is
then active for approx. 30 seconds and
automatically switches off again.
Alternatively, it can be switched off at any
time by pressing the Shift key again.
17. Power: ON/OFF
General
This universal remote control is one 8 in 1
remote control and can operate following
device types: TV, STB, CBL, AUDIO, AUX,
VCR, CD, DVD. (e.g. DVD-recorder/Player,
video recorders, boosters, tuners, etc.).
The lettering of the keys does not describe
the device type to be programmed, it is used
therefore only for the easier overview.
Note down please the codes of your devices
which you used for the programming. If the
codes should be e.g. to a battery change no
more not stored, you can program the remote
control so more quickly.
They must program a four-digit device code
to a source key (TV, STB, CBL, AUDIO, AUX,
VCR, CD, DVD) for every device which you
would like to operate with the universal
remote control.
Video recorder:
for the code search please
inserted a tape.
Programming device codes
Entering device code after code set
The codes of the corresponding devices are
the code list, to take that is enclosed in this
operating manual.
• Turn on the device manually.
• Hold the key setup (4) pressed for approx.
3 seconds until the red LED (1) lights up
permanently.
• Press the source key (3) (TV, STB, CBL,
AUDIO, AUX, VCR, CD, DVD) shortly.
! Press the „Mode“ (2) button before using
the group of devices (AUX, AMP, DVB-T,
CBL).
• You distribute the corresponding four-digit
code then the code table one.
• To the confirmation of every keystroke the
red LED (1) goes out shortly.
g
Operating Instructions
• If the code input was valid, the red LED (1)
goes out according to the input of the last
place.
• Press SHIFT (16) briefly and then OK (15)
to save the code. The LED (1) briefly goes
out.
• Briefly press the Shift (16) key.
• An invalid code was entered, the red
LED (1) flashes for three seconds before it
goes out. Should the device not reacts;
you repeat the programming where
appropriate with another code. Please try
out all codes indicated for your brand.
• Select the code which all available
commands of your remote control react to
correctly.
• You should not have also any success in
this way, then you attempt it with that one
„search run automatic in the chapter“
described search method.
Manual code search run
• Turn on the device manually.
• Hold the key setup (4) pressed for approx.
3 seconds until the red LED lights up
permanently.
• Press the source key (3) (TV, STB, CBL,
AUDIO, AUX, VCR, CD, DVD) shortly.
! Press the „Mode“ (2) button before using
the group of devices (AUX, AMP, DVB-T,
CBL).
• You press repeatedly the key POWER (17)
after each other (this can be up to 350
times), only at VCR (Video recorders) asks
the key P+ (14) or P- (14)
• to the device that is supposed to be
operated, off, or changes the channel or
reacts correspondingly. The code-search
is begun with the code number currently
stored on the cluster.
• Press SHIFT (16) briefly and then OK (15)
to save the code. The LED (1) briefly goes
out.
• Briefly press the Shift (16) key.
• Due to the extensive number of different
possible codes, up to 350 possible codes
are preset per device type. In individual
cases, it may be possible that only
the most common main functions are
available. The procedure described may
be unsuccessful for some special device
models.
Automatic search run
If your device does not respond to the remote
control although you tried out all codes
performed for your device type and the
corresponding brand, you attempt it with the
automatic search run. Through that you
can find also such codes of such brands
which are not performed in the device code
list.
• Turn on the device manually
• Hold the key setup (4) pressed for approx.
3 seconds until the red LED (1) lights up
permanently.
• Press the source key (3) (TV, STB, CBL,
AUDIO, AUX, VCR, CD, DVD) shortly.
! Press the „Mode“ (2) button before using
the group of devices (AUX, AMP, DVB-T,
CBL).
• Focus the remote control on the device
and press the key P+ (14) once shortly.
• If the device does not have any
program-function, you press the key
POWER (17) instead of the P+ (14).
• The remote control starts the code
search after 6 seconds and sends in the
1 second’s clock pulse (see also next
section) after each other all codes. At
every sending the red LED lights up.
• As soon as the device responds to the
remote control, press SHIFT (16) and then
OK (15). Briefly press the Shift (16) key. If
you do not press OK in time, press PROG-
(14) to return step-by-step to the code
where the device responded.
