97096C (Rev. D - 9/99)
HRF - ER*B HRF - SR*B HRF - SER*B
PAGE 4
PART NO.
ITEM NO.
PARTS LIST
Drain
Drain-Aztec Gold
Retaining Nut
Strainer
Strainer-Aztec Gold
Tailpipe Ferrule
Tailpipe Ferrule-Aztec Gold
Push Button
Push Button-Aztec Gold
Push Button Sleeve
Push Button Sleeve-Aztec Gold
Regulator Holder
Bubbler
Bubbler-Aztec Gold
Regulator
Setscrew #6-32 x .31"
Screw #8-32 x .25"
Strainer
Fountain Arm-Short
Fountain Arm-Short Aztec Gold
Fountain Arm-Extended
Fountain Arm-Extended Aztec Gold
Bottom Cover Plate-Short
Bottom Cover Plate-Extended
Back Panel HRF-SER
Back Panel HRF-SER Aztec Gold
Back Panel HRF-ER/SR
Back Panel HRF-ER/SR Aztec Gold
Hex Nut
Speed Nut
Bracket-Regulator Mounting
Lower Panel HRF-SER
Lower Panel HRF-SER Aztec Gold
Lower Panel HRF-ER/SR
Lower Panel HRF-ER/SR Aztec Gold
Union - 3/8" x 1/4"
Union - 3/8"
Tee - 3/8"
Assy-Bubbler Nipple
Tube-Poly 1/4 x .040 Wall
LK464
LK464AG
15005C
40038C
45364C
40619C
45360C
45662C
45408C
45663C
45411C
50986C
51544C
45396C
61313C
70022C
70426C
55996C
55001035
27571C
55001038
27573C
55000661
55000665
26839C
27542C
26837C
27539C
40045C
70055C
27057C
27026C
27580C
26833C
27578C
70745C
70870C
70852C
15008C
55994C
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
DESCRIPTION
FIG. 5
2222 CAMDEN COURT
OAK BROOK, IL 60523
630.574.3500
PRINTED IN U.S.A.
SEE FIG. 6
SEE
FIG. 5
8
15
13
12
1
11,14,17
3,4
19
FIG. 6
Orifice Assy:
Mineral deposits on orifice can cause water flow to spurt or not regulate. Mineral deposits may
be removed from the orifice with a small round file not over 1/8" diameter or small diameter wire.
CAUTION: DO NOT
file or cut orifice material.
Stream Regulator:
If orifice is clean, regulate flow as in
START UP
instructions. If replacement is
necessary, see parts list for correct regulator part number.
Actuation of Quick Connect Water Fittings:
Cooler is provided with lead-free connectors which utilize an
o-ring water seal. To remove tubing from the fitting, relieve water pressure, push in on the gray collar while
pulling on the tubing.(see Fig.2) To insert tubing, push tube straight into fitting until it reaches a positive stop,
approximately 3/4".
CAUTION: Cleaning of Aztec Gold Models requires special care.
Outer surfaces must be cleaned with
mild detergent or a mixture of vinegar and water only, rinsed and wiped dry. Abrasive and acidic cleaners may
eventually damage the Aztec Gold finish.
HRF - ER / SR / SER COOLER INSTALLATION
1. Install remote chiller.
Remove front panel of chiller. Remove and discard cardboard inner pack from
between compressor and side panel. Slide chiller onto the shelf and position it to the left within the guides
on the shelf.
NOTE:
Building construction must allow for adequate air flow on both sides, top, and back of chiller. A
minimum of 4" (102mm) on both sides and top is required. See chiller instructions for additional instructions.
2. Make water supply connections.
Attach an unplated copper water inlet line and a service stop (not
provided) to the chiller. Inlet port is marked on the chiller (3/8" O.D. copper tube). Bend the copper tube
(provided) at an appropriate length from chiller to opening in frame. Install a 3/8" O.D. tube tee fitting (provided)
on the marked chiller outlet port. Turn on the water supply and flush the line thoroughly.
3. Hang the upper panel on the mounting frame hanger.
Align holes in the panel with the holes in the
mounting frame. Be sure that panel is engaged with hanger at top of frame before releasing it.
4. Install fountain.
Remove access cover plate on underside of fountains and save the screws. Mount the
fountains to the upper panel and the wall frame with (4) 5/16" x 3/4" (19mm) long bolts and nuts (provided).
Tighten securely.
NOTE:
The short fountain should be mounted to the upper left hand side of the panel.
5. Remove elbow from end of p-trap
and attach it to drain tube. Re-attach elbow to p-trap and cut waste
tube to required length using plumbing hardware and trap as a guide.
6. Make connection between remote chiller outlet tube and fountain strainer.
Insert the water inlet line
into inlet side of strainer by pushing it in until it reaches a positive stop, approximately 3/4" (19mm). Turn on
water supply and check for leaks.
DO NOT SOLDER TUBES INSERTED INTO THE STRAINER AS
DAMAGE TO THE O-RINGS MAY RESULT.
7. These products are designed
to operate on 20-105 PSIG supply line pressure. If inlet pressure is above
105 PSIG, a pressure regulator must be installed in the supply line. Any damage caused by reason of
connecting these products to supply line pressures lower than 20 PSIG or higher than 105 PSIG is not covered
by warranty.
8. Make electrical connections to the chiller.
See chiller instructions.
9. Check stream height from bubbler.
Stream height is factory set at 45-50 PSI. If supply pressure varies
greatly from this, remove items 5 & 6 and adjust the screw on regulator (item 9). Clockwise adjustment will
raise stream height and counter-clockwise will lower stream height. For best adjustment stream height should
be approximately 1-1/2" (38mm) above the bubbler guard. (See Figure 6)
10. Mount lower panel.
Loosen the (2) #10-24 x 5/8" (16mm) screws at frame bottom lip. Slide upper tongue
of lower panel under lower edge of already installed upper panel. Tighten previously loosened screws securely.
11. Replace bottom access panel
to fountain basin using screws provided. Tighten securely.
TROUBLE SHOOTING & MAINTENANCE
CHILLER
INLET
21
20
CHILLER
OUTLET
12
TO BUBBLER
HRF - ER / SR
TUBE ROUTING
HRF - SER
TUBE ROUTING
TO BUBBLER
TO BUBBLER
12
22
CHILLER
OUTLET
CHILLER
INLET
20
5
6
16
2
9
7
10
18
24
23
