Haier QPSA13, Руководство пользователя и инструкция по установке

Страница: 6 / 48

6
49-5000467 Rev. 1
ENGLISH
Cool Mode
Use the COOL mode for cooling.
To set the COOL mode:
1. Press the MODE pad until the COOL indicator light is lit.
2. Press the FANóäç÷òöè÷ÑÒÐÑÖÎÍÒÞÖòõÕØàéäñ
speed.
3. Press + or - to set the desired temperature between 61°F
and 89°F in 1°F increments.
After settings have been made, the display will change back
to show the room temperature.
The temperature control is used to maintain the room
temperature. The compressor will cycle on and off to keep
the room at the set level of comfort. Set the temperature
control at a lower number and the indoor air will become
cooler. Set the temperature control at a higher number
and the indoor air will become warmer. NOTE:Òé÷ëèäìõ
conditioner is off and is then turned on while set to COOL,
it will take approximately 3 minutes for the compressor to
start and cooling to begin.
Cooling Descriptions
For Normal Cooling—Select the COOL mode and HIGH,
MEDIUM, or LOW fan speed with a middle set temperature.
For Maximum Cooling—Select the COOL mode
and HIGH fan speed with a lower set temperature.
For Quieter & Nighttime Cooling—Select the COOL mode
and LOW fan speed with a middle set temperature.
×ØÝÎIf you switch from COOL or DRY mode setting to
OFF, wait 3 minutes before restarting.
DRY Mode—Dehumidification
Use the DRY mode to provide dehumidification only. The
fan will run at a fixed speed at this setting, so a fan speed
cannot be set. Keep windows and doors closed for the best
dehumidifying effects.
To set the DRY mode:
•Press the MODE pad until the DRY indicator light is lit.
Òñ÷ëèÍÛâðòçèäöè÷÷èðóèõä÷øõèúìïïñò÷åèçìöóïäüèç
Êé÷èõÍÛâðòçèëäöåèèñöè÷÷ëèçìöóïäüúìïïæëäñêèåäæî÷ò
show the room temperature.
NOTE: Òéüòøöúì÷æëéõòðäÍÛâöè÷÷ìñê÷òØÏÏòõ÷òäéäñ
setting, wait at least 3 minutes before switching back to a
ÍÛâöè÷÷ìñê
FAN Mode
Use the FAN mode to provide air circulation and filtering
without cooling.
To set the FAN mode:
• Press the FAN pad until the desired indicator light for high,
medium, or low fan speed is lit.
Since fan only settings do not provide cooling, a set
÷èðóèõä÷øõèúìïïñò÷åèçìöóïäüèçÊé÷èõÏÊ×öóèèçëäö
been set, the display will change back to show the room
temperature.
The exhaust hose and window kit do not need to be installed
when operating in fan mode.”
HEAT Mode
Use the Heat mode at Low, Med, High or Auto Fan Speed
for heating. Use the Temperature Increase (+) /Decrease (-)
pads to set the desired temperature between 61°F and 86°F
in 1°F increments. An electronic thermostat is used to maintain the room
temperature. The heater will cycle on and off to keep the
room at the set level of comfort.
Power Outage Recovery Feature
In the case of a power outage or interruption, the unit will
automatically re-start in the settings last used after the
power is restored. NOTE: If the TIMER was set before the power outage, it will
need to be reset after power is restored.
The display will always default to show the room temperature.
When the air conditioner is turned on, it will automatically start in the last mode and fan settings selected.
CONTROLS