Haier PJF2-200 Скачать руководство пользователя страница 10

Страница: 10 / 16

Haier solar water heater

Directions for use

Solar energy indication light (green)

While it is lighted up, it is indicated that water heater is in solar energy heating working

mode.

Instant heating indication light (green/red)

While the green light is on, it is indicated that water heater is in instant heating working

mode. While the red light is on, it is indicated that water heater starts electric heating

working mode. (when the temperature is heated to the set value, working mode will be

automatically switched to solar heating mode from instant heating mode. At the same time

heating indication light is off and solar indication light is on.)

Presetted heating indication light (green/red)

While the green light is on, it is indicated that water heater is in presetted heating working

mode. While the red light is on, it is indicated that water heater starts electric heating

working mode. (when the temperature is heated to the set value, indication light turns

green.)

Intelligent heating indication light (green/red)

While the green light is on, it is indicated that water heater is in intelligent heating working

mode. While the red light is on, it is indicated that water heater starts electric heating

working mode. (when the temperature is heated to the set value, indication light turns

green.)

Temperature indication light of water storage tank (yellow)

While it is lighted up, it is indicated that temperature displayed in temperature displaying

zone is current temperature of water storage tank.

Temperature indication light of solar collector (red)

While it is lighted up, it is indicated that temperature displayed in temperature displaying

zone is current output water temperature of solar collector.

Clock time display/ parameter setting display (green) ( A and B)

In normal state it display current time set by the user, and the clock can be reset only under

the solar energy heating mode ( green indication light of solar energy is on). Different

Mode Settings will display Corresponding parameters.

Temperature indicator (green)

Display current temperature of water storage tank and solar collector in turn.

Содержание PJF2-200

















Результаты поиска

Содержание PJF2-200

Отзывы:

Бренды по названию

Популярные бренды

Haier PJF2-200, Руководство по эксплуатации

Результаты поиска

Содержание PJF2-200

Отзывы:

Бренды по названию

Популярные бренды