Haier PBFS21EDAB Скачать руководство пользователя страница 35

Страница: 35 / 36

7.Other

Icemaker and defrost details

1.You can manually start a defrost cycle according to Pressing FRZ< , FRZ> temp

adjust keys and RESET(or TEST) for 3 seconds.There will be "T1,T1" on display

panel.

2.Generally speaking,there will be a deforst cycle after 7 hours working of

compressor.If there is less door openings or the temperature is proper,the defrost

cycle will increase,maybe 90 hours.

3.And the humidity sensor does not matter with the defrost cycle.

4.Center mullion heater will be function under certain time proportion if the

humidity is heavy or more door openings.

5.The Center mullion heater will stop working under proper humidity or less door

openings.

6.And it's 25W,529

.There are the technical datas in connect diagram in service

manual.

7.The icemaker will stop when drawer is opened even in harvest time.

8.You can manually start the icemaker according to pressing FRZ< and REF>

temp adjust keys for 3 seconds,the icemaker will cycle one time.

9.You can adjust the water lever according to controlling the time of water

infusing.Press the 2 time adjust keys for 3 seconds,then the function of water

infusing is available.

10.When you adjust the water level,you will see “CC”.It means milliliter.

Other

Содержание PBFS21EDAB





































Результаты поиска

Содержание PBFS21EDAB

Отзывы:

Бренды по названию

Популярные бренды

Haier PBFS21EDAB, Руководство по обслуживанию

Результаты поиска

Содержание PBFS21EDAB

Отзывы:

Бренды по названию

Популярные бренды