background image

 

13 

Information for cooker hood

 

 

 

ENVIRONMENTAL PROTECTION:

 

  

This product is marked with the symbol on the selective sorting of waste electronic equipment. This 
means that this product must not be disposed of with household waste but must be supported by a 
system of selective collection in accordance with Directive 2002/96/EC. It will then be recycled or 
dismantled to minimize impacts on the environment, electrical and electronic products are potentially 
dangerous for the environment and human health due to the presence of hazardous substances.

 

 

For more information, please contact your local or regional authorities.

 

 

Note:

 

 

The following shows how to reduce total environmental impact (e.g. energy use) of the cooking process).

 

 

(13) 

Install the cooker hood in a proper place where there is efficient ventilation. 

 
(14) 

Clean the cooker hood regularly so as not to block the airway. 

 
(15) 

Remember to switch off the cooker hood light after cooking. 

 
(16) 

Remember to switch off the cooker hood after cooking. 

 

Information for dismantling

 

 

Do not dismantle the appliance in a way which is not shown in the user manual. The appliance could not be 
dismantled by user. At the end of life, the appliance should not be disposed of with household waste. Check with 
you Local Authority or retainer for recycling advice.

 

 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

 

12 
 
 

Содержание IT9001





















Отзывы: