background image

15

Common phenomena

Phenomena

Explanation

The wash procedure is paused

The digitron displays E0.

The safety switch acts, and the spin-
ning cannot work. Amend  twice
automatically ,The digitron displays E3.

The water filling does not work, or is 
slow. The digital displays E4.

The drainage cannot work, or is too slow.
The digitron displays E1.

 It stops running in midway. The digitron
displays E2.

The top lid is not closed.

The top lid is opened during reserve 

    procedure.

Close the top lid.

Close the top lid.

Is the drain hose put down?
Is the drain hose blocked?

   Put down the drain hose. Open and close the
   top lid once.

Clean the foreign material. Open and close
the top lid once.

Are the laundries put slantingly?
Is the machine slanting?

Reorder the laundries. Close the top lid.

Placed the machine horizontally, open 

    and close the top lid once.

Is the water tap opened, or is there water

    supply failure?

Is the water inlet valve blocked?
Is the water pressure too low?

Open the water tap. Open and close the 

   top lid once.

Clean the water inlet valve then open and 

    close the top lid once.

Use after the water pressure is normal.

The water level sensor is bad.

Please contact the after-sales

     service department.

Is the machine slanting?
Are the laundries put slantingly in spinning?
Are there any foreign materials?

Is the screw of the jointer of water

   inlet hose loose or awry?

Adjust the machine to be even
Reorder the laundries and close the top lid.
Remove the foreign materials.

Fasten the screw of the jointer properly.

The water tap leaks

The digitron displays E6.

There's abnormal sound
 inside the machine

Phenomenan                             The reason                            How to settle

Trouble-shooting  Answer  to question

(If  there's  breakdown,  please pull off the power plug before checking)  The following phenomena are  not breakdowns 
sometimes.  Please confirm again before sending it to repair. If there are real breakdowns, please come to the special
maintenance department or after-sale service department of our company. Do not repair it by yourself.

The machine does 
not act

Not wash

Not spin

Is there power failure?
Is the power plug inserted tightly?
Is the water level reached preset position?

Please use it when there's power supply.
Insert the power plug tightly.
Fill water to the preset position.

Is the power plug inserted tightly?
Is the top lid closed reliably?
Are the laundries set flat?

Insert the power plug tightly.
Close the top lid.
Set the laundries flat.

It is the water remained in the factory inspection
of performance.

Balance the laundries to avoid slanting.

The program is setting the drain time. Some time is
 needed before it starts spinning.

The spinning is intermittent when it starts.

There may be some water flowing out of 
the drain hose in the first use of the machine.

Push the "spin" button to  select "Spin", 
but it doesn't work.

The cloth sensor is checking the cloth, it will add 
water after 48 seconds.

The pulsator pauses during water inlet in wash 
and rinse.

It is to avoid splashing during water inlet.

It is the special resume function.

In the case of power failure

or the power plug is loose during washing, the machine can
save the running program, and resume the program after
 the power supply is recovered. You do not need to set the
program again.

When the power plug is inserted, computer
board indicator is switched on, and the machine
starts working

Содержание HWM65-0566



















Отзывы: