To connect the drain pipe
Ring the drain pipe on the joint;
Fix the pipe clamp to the groove of drain pipe;
Insert the drain pipe into a floor drainer;
Extend the drain pipe.
State of
extension hose
Height
Length
Rise midway
Within 10cm
Within 1m
Not rise
midway
-
Within 3m
If the drain pipe is too long, remove the pipe sleeve, cut
off the groove part of drain pipe, and then insert the pipe
sleeve into the front end of drain pipe.
If there is a need to extend the drain pipe or change the direction of drain pipe, please contact our
After-sales Service Department.
To remove the packaging
bolts
Packaging bolts are used to fix internal components of the
washer-dryer during transport and should be removed before
using the washer-dryer.
Screw off all the packaging bolts with a wrench and pull
them out in the direction as shown in the right figure;
Insert the heave of packaging bolt cover into the
packaging bolt cover hole, and then buckle the packaging
bolt cover into the packaging bolt hole in the direction of
arrow as shown in the right figure.
Please keep the dismantled packaging bolts in a safe place
for future handling of the washer-dryer.
To adjust the front
adjustable
foot (2)
Loosen the adjusting nut, and then
adjust the adjustable foot (as shown in Fig.
1) until the air bubble of level gauge is in
the red circle (as shown in Fig. 2);
Tighten the adjusting nut (as shown in Fig. 3).
Packaging
bolt hole
Packaging bolt
cover hole
Heave
Fig. 1
Fig. 2
Fig. 3
Loosen
High
Low
Tighten
Adjusting
nut
Adjustable foot
Within 10cm
Pipe clamp
Floor
drainer
Floor
Joint Groove Drain pipe
Within 1m
Pipe sleeve
Drain outlet
Stay a space
Groove
Pipe sleeve
Pi
Tighten
Ad
Adjju
dd
nut
Loo
High
Low
en
Before removing the
packaging
blts, please fix the Bottom cover to the bottom of the washer dryer. Lay down
the machine, adjust the Bottom cover with the six holes corresponding the screw holes.Then tighten the screws
and fix it thus securely to the bottom of the machine.
To install the Bottom cover
Distributor box
Please select suitable non-foaming or low-foaming washing powder/detergent for automatic drum washer;
As for the dosage of detergent, please refer to the instructions for detergent. Excessive detergent may result
in too many bubbles and spill as well as affect its dissolution;
The level of softener or liquid detergent must not be higher than the “MAX” mark on the siphon cap.
Concentrated softener or liquid detergent should be diluted before being added into the distributor box. Excessive
softener may damage synthetic fiber. As for the dosage of softener, please refer to its instructions.
There may be a
little water in the distributor
box after the selected
program ends. It is normal
and the water is the makeup
water or condensate water in
the process of program
running.
Drying filter box
d
a
e
r
h
t
e
h
t
r
e
tl
if
o
t
d
e
s
u
si
x
o
b
r
e
tl
if
g
n
i
y
r
d
e
h
T
scraps produced in the process of drying.
e
c
a
l
p
n
i
x
o
b
r
e
tl
if
g
n
i
y
r
d
e
h
t
ll
a
ts
n
i
o
t
e
r
u
s
e
B
m
r
a
l
a
ll
i
w
r
e
h
s
a
w
e
h
t
e
si
w
r
e
h
t
o
;
g
n
i
y
r
d
e
r
o
f
e
b
to remind you.
Drawer
The drawer may be used to store spare
washing powder and detergent, etc.
o
t
n
i
t
n
e
g
r
e
t
e
d
r
o
r
e
d
w
o
p
g
n
i
h
s
a
w
r
u
o
p
t
o
n
o
D
the drawer to prevent the drawer from being
r
e
f
e
r
e
s
a
e
l
p
,r
e
w
a
r
d
e
h
t
g
n
is
u
n
e
h
W
.
d
e
t
a
n
i
m
a
t
n
o
c
to the contents in the section of “Precautions for Use”.
Door-opening button
e (the water)
t
a
ts
e
f
a
s
e
h
t
n
i
si
r
e
y
r
d
-r
e
h
s
a
w
e
h
t
n
e
h
W
t glass, the
h
g
is
f
o
e
g
d
e
r
e
w
o
l
e
h
t
w
o
l
e
b
si
l
e
v
e
l
temperature inside of the drum is below
50
the inner drum is not rotating) and the door is
y pressing this
b
d
e
n
e
p
o
e
b
n
a
c
r
o
o
d
e
h
t
,
d
e
k
c
o
l
n
u
button.
Add solid
washing power
Add liquid
softener
Add liquid
detergent or
bleach
Siphon cap
°C and
