21
Troubleshooting
Troubleshooting without display code
Washing machine
Programme is not yet started.
Press “Start/Pause“ button.
fails to operate.
Door is not properly closed.
Close the door properly.
Machine has not been switched on. Switch the machine on.
Power failure.
Check power supply.
Washing machine
No chosen programme.
Set programme and start it.
will not be filled
No water.
Check water tap.
with water.
Inlet hose is kniked.
Check inlet hose.
Inlet hose filter is blocked.
Unblock inlet hose filter.
Water pressure is less than
Check water pressure.
0,03 MPa.
Water supply failure.
Ensure the water supply.
Machine is draining
Height of drain hose is
Make sure that drain hose
while being filled
below 80 cm.
is properly installed.
Drain hose end could
reach into water.
lever
In case of power failure
The current programme and its setting will be saved only
s
i
t
r
a
t
s
e
l
c
y
c
e
m
m
a
r
g
o
r
p
w
e
n
a
y
l
b
a
b
o
r
P
.
e
m
it
t
r
o
h
s
a
r
o
f
needed.
If a power failure cuts an operating wash programme door
opening is mechanically blocked.To get out any laundry
water level should not be seen in the glassy porthole of the
door - danger of burns!
.
“
r
e
tl
fi
p
m
u
P
“
n
i
d
e
b
i
r
c
s
e
d
s
a
d
e
r
e
w
o
l
e
b
o
t
s
a
h
l
e
v
e
l
r
e
t
a
W
Not till then pull lever beneath service flap until door is
unlocked by a gentle click.Afterwards refix all parts.
20
Troubleshooting
Display code
n
o
i
t
u
l
o
S
e
s
u
a
C
e
d
o
C
Auto
Lo
/HALF
/FULL
/HI
Automatic
Weighing the laundry load in
the drum.
load detection.
Laundry weight detection in progress, please
wait until program cycle time is displayed.
Please wait until program cycle time is
displayed: Lo = small load;HALF = half load;
FULL = optimized weight load;
HI = full load.
1:25
Remaining wash cycle time.
Refer to additional symbol.
19:30
Remaining wash cycle time.
End is likely delayed - refer to symbol.
Lock
Door cannot be opened due to
water level or hot water in the
drum.
Wait to the end of program or cancel the
program and select the drain program. In
case of hot water is in the drum, to avoid
scalding, select a handwash program and
wash several minutes and then select a
draining program before open the door.
End
End of cycle.
E1
Drainage error, water not emptied. Clean pump filter.
Check drain hose for blockage
and proper
installation.
E2
Lock - error.
Shut the door properly.
E4
Water level not reached after 8
minutes.
Check if water supply and water pressure
is normal.
Drain hose is self-syphoning.
E8
Water protective level - error.
Auto release.Otherwise contact the
After sales service.
F3
Temperature sensor - error.
Contact the After sales service.
F4
Heating error (Appears at the end of
a cycle .)
Contact theAfter sales service.
F7
Motor - error.
Contact theAfter sales service.
Fb
Water overflow.
Close tap immediately.
Contact theAfter sales service.
FA
Water level sensor error.
Contact theAfter sales service.
FC
Electronic control - error.
Contact theAfter sales service.
Unb
Unbalanced load and not able to
spin.
Check and balance the laundry load in the
drum. Also reduce the load if too heavy.
Restart with a spin program.
Warning!
Code
Fb
: Water-overflow protection is placed on deepest part of appliance. In case of leacka-
ge all functions will be shut down automatically except drain pump which will be activated for
safety reasons.
Содержание HW70-B1426
Страница 86: ......
Страница 126: ...21 0 03 80 20 Auto Lo HALF FULL HI Lock End E1 E2 F3 8 E4 F4 F7 E8 FA FC Fb lever ...