Haier HSU18XH7-G - Ductless Split Indoor Wall Mount Unit Heat..., Руководство по обслуживанию

Страница: 26 / 60

Parts and Functions
Remote controller
If the unit which you purchased has healthy function,follow it.If not,please ignore.
NOTE:
Cooling only unit do not have displays and functions related with heating
Outdoor Unit
Display board
1 4 2
3
5
Signal receiver hole
ON/OFF display
4
2
3
1
5
TIMER ON\OFF display
SLEEP display
Ambient temp.display
When receiving the remote
control signal, display the set
displayed and this room
time the room temperature is
temperature and in the rest
temperature is only for reference.
Note to the power failure resume:
press the sleep button ten times in five seconds and
enter function after hearing four sounds.And press
the sleep button ten times within five seconds and
leave this function after hearing two sounds.
TIMER ON-OFF display
8
Actual inlet grille may vary from the one shown in the
manual according to the product purchased
(adjust up and down air flow
Don't adjust it manually)
(adjust left and right air flow)
Vertical blade
COOL\HEAT\Dry\
AUTO display
1 4
Indoor Unit
OUTLET
INLET
CONNECTING PIPING AND ELECTRICAL WIRING
DRAIN HOSE
1
2
3
4
1
2
3
Remove the battery cover;
Load the batteries as
illustrated. 2 R-03 batteries,
resetting key(cylinder);
Be sure that the loading
is in line with the " + "/"-";
Load the battery,then put on the cover again.
The distance between the signal transmission head and the
receiver hole should be within 7m without any obstacle as well.
When electronic-started type fluorescent lamp or change-over
so the distance to the indoor unit should be shorter.
wireless telephone is installed in the type fluorescent lamp or
room, the receiver is apt to be disturbed in receivingthe signals,
Note:
Full display or unclear display during operation indicates the
ries have been used up.Please change batteries.
If the remote controller can't run normally during operation,
reload several minutes later.
batte
remove the batteries and
Remove the batteries in case unit won't be in usage for a long period.
If there are any display after taking-out, just need to press reset key
Hint:
Loading of the battery
please
Clock set
Press CLOCK button, "AM" or "PM" flashes.
Press or to set correct time. Each press will
change quickly. After time setting is confirmed,press SET,
"AM "and "PM" stop flashing,while clock starts working.
increase or decrease 1min. If the button is kept pressed,time will
25. .
SWING button
9. ON/OFF button
10. TIMER ON display
11. FAN SPEED display
LOW HI MED AUTO
12. LOCK display
13. SWING display
14. SLEEP display
Operation mode
AUTO FAN COOL DRY
Remote controller
16. Operation mode display
18. POWER/SOFT display
19.
20.
TEMP display
21.
TIMER OFF display
22.
CLOCK display
23.
TEMP button
24.
FAN SPEED button
28. SET button
26. POWER/SOFT button
If pressed, the other buttons
be disabled.Press it once
again,lock will be cancelled.
29. LOCK
HEAT
17.Signal sending display
2
11
12
13
14
16
17
18
19
20
21
22
23
24
25
28
26
29
30
HEALTH AIRFLOW button
will
When the remote controller
30. RESET
button
button
appears abnormal,use a
sharp pointed article to press
this button to reset the remote
controller normal.
5. SLEEP button
Used to select CODE A or B
will be displayed on
explanation.
1.CODE
3. TIMER button
4. CLOCK button
8. MODE button
7. HOUR button
2.LIGHT button
Control the lightening and
the indoor
which
extinguishing of
LED display board.
LCD.
special
Please select A without
6
5
2
1 4
3
Inlet grille
Inlet
Air Purifying Filter (inside)
Outlet
Horizontal flap
6
4
2
1 5
3
5
2
1
5
3
6
4
7
7
HSU-18 24HEK13/R2 System Configuration
Domestic Air Conditioner
24