Haier HLT20E страница 14 Скачать руководство пользователя

Страница: 14 / 15

MAINTENANCE SERVICE AND TROUBLE SHOOTING

Is the water pressure lower?

It is special phenomena for
washer with pump.

Wait for the normal water
pressure before use.

It is the water remained in the factory
inspection of performance.

Phenomenan The reason How to settle

Common phenomena

Phenomena Explanation

The program is setting the drain time. Some
time is needed before it starts spinning.

The top lid is not closed.

Is the drain hose put down?
Is the drain hose blocked
by foreign material?

Is the jointer screw of the
water inlet hose is loose
or twisted awry?

Is there power failure?
Is the power plug loose?

Is the machine slanting?
Are the laundries slanting
in spinning?

Fasten the jointer screw
properly.

If do not need continue
draining, you can raise
the entrance of drain hose
and let water flow back
inner tub. .

Close the top lid.

Put down the drain hose.
Open and close the top lid once.
Clean the foreign material.
Open and close the top lid once.

Use it when the power is on.
Insert the power plug tightly.

Level the machine properly.
Re-order the laundries.

There may be some water flowing out of
the drain hose in the first use of the machine.

Rotate the "Process selector" knob to
select "Spin", but it doesn't work.

The water faucet leaks.

During draining, the washer
continues draining when push
in programme selector knob.

The machine does not act.

There's abnormal sound
inside the machine.

In washing,rinsing,spinning,
the machine stops running.

No water filling or
filling slowly

Содержание HLT20E
















Результаты поиска

Содержание HLT20E

Отзывы:

Похожие инструкции для HLT20E

Бренды по названию

Популярные бренды

Haier HLT20E, Руководство по обслуживанию

Результаты поиска

Содержание HLT20E

Отзывы:

Похожие инструкции для HLT20E

Бренды по названию

Популярные бренды