19
GBGB
Refrigerator Usage Tips
• Radish leaves should be cut off to prevent the absorption of
nutrients by the leaves.
• You may move egg cartons to a suitable storage location
according to need and choose the right egg carton according
to the amount of eggs.
• Zucchinis, melons, papayas, bananas, and pineapples, etc.
in a refrigerated state will promote their metabolism, so they
shall not be refrigerated. But for unmatured fruit, it is better to
store them in a refrigeration compartment for a certain time to
promote their maturation.
• Some foods, such as onions, garlic, ginger, water chestnuts,
tubers, etc., can be stored for long periods at room
temperature, so it is unnecessary to store them in the
refrigerator.
• Fresh vegetable should be washed and then placed into the
refrigerator in order to prevent the breeding or spreading of
bacteria in the refrigerator.
Precautions for energy-saving
usage
• The refrigerator should be installed in a cool and well
ventilated room, keep it away from heat, and avoid direct
exposure to sunlight as much as possible.
• Minimize the times and frequencies that the doors are
opened. For example: store food regularly, which can reduce
the access times for opening the doors.
• Cool hot foods or drinks first and then put them in the
refrigerator;
• The foods that need to be thawed should be placed first into
the refrigerator compartment (or MY ZONE), so you can use
the lower temperature of the frozen food to cool the food in
the refrigerating chamber (or MY ZONE);
• Do not overfill the refrigerator to avoid obstructing the air flow;
• For the temperature setting of the refrigerator, the lower the
temperature is set, the greater the energy consumption of the
refrigerator is. Based upon the premise of actualizing the food
storage conditions, the temperature inside the refrigerator
should be set as high as possible.
• If you need to use a relatively large amount of space in the
freezer compartment, the small freezer drawer and the gear
connecting rod can be removed, then food can be directly
put in and taken out through the freezer compartment’s
glass partition, at the same time this can also decrease the
refrigerator’s energy consumption;
• Leave as much gap or space around the appliance as
practical to ensure good ventilation. See page 7.
If the ventilation is restricted this will increase the running /
operating costs and the appliance will not achieve its energy
consumption data.
• Keep door seals clean so that the door always closes
correctly.
Usage of the refrigerator’s water
reservoir assembly
This model of refrigerator features a water reservoir assembly
which is put into the left door assembly. The water pump that is
set into the refrigerator’s left door assembly extracts water from
the water reservoir assembly, and pumps it via the water piping
into the semiautomatic icemaker’s small freezer drawer.
Users need to manually fill the water reservoir assembly with
water. The filling method is as per the following:
1. Turn the vertical ridges 90 degrees. Press the buttons on
both sides of the water reservoir assembly.
2. After firmly pressing in the push buttons, make the water
reservoir assembly level and then gently pull it out forward.
3. Remove the lid on the back of the water reservoir assembly
counterclockwise, then fill with fresh drinking water.
Reattach the lid.
4. When you need to reinstall it, you can reinstall it by
reversing the above operation procedures.
Rotate counterclockwise to unscrew the
lid and fill with water, after filling with water
rotate it clockwise to screw it on tight.
Water reservoir filler knob
(located on the back of the assembly)
Caution
The water reservoir assembly was already installed and
commissioned prior to leaving the factory. If you need to clean
the water reservoir assembly, refer to “Cleaning the water
reservoir assembly,” in order to prevent the water reservoir
assembly from getting damaged.
Warning
Use only fresh drinking water!
Cleaning the water reservoir assembly
1. Please pry apart the latches (total of 4 latches) on the front,
rear, and right and left.
2. Separate the upper portion of the water reservoir assembly
from the bottom portion.
3. Clean out each section, then wipe them dry after they are
clean. Warm water and a neutral detergent are sufficient for
cleaning.
4. When you need to reinstall it, you can reinstall it by
reversing the above operation procedures.