manualshive.com logo in svg

Haier HB2400VD1M20, Руководство по обслуживанию, Страница: 16 / 18

Поделиться
Скачать
Haier HB2400VD1M20 Скачать руководство пользователя страница 16

When an optional electric heat kit is installed refer to the electrical requirements for that kit. The 
ampacity and over-current protection shown above is 

onl y

 for "HB" air handlers installed 

without

a heat kit

.

Port definition: 

C1, C2: power input port, 24VAC; 

C3: control signal input port, 24V; 

P1, P2, P3: fan motor control port --- P1 is COM port, P3 is normal OFF, P2 is normal OPEN; 

    K1: fan motor relay 

Function description 

1. K1 will open 15 seconds later after there is 24V signal from C3; 

2. K1 will open 30 seconds later after there is no signal from C3;   

3. AC contactor control the electric heater solely. 

Connecte P1 with netural wire of fan motor, connect normal OPEN port P2 with power input 

port of AC contactor, supply P1 the power of fan motor when there is signal from C3. connect 

normal OFF port P3 with power output port of AC contactor, to ensure the fan motor work 

whenever there is or is not control signal during heater woring. 

C1

C2

C3

P1

P2

P3

K1

Electric control function for 

air handlers

A MEANS OF STRAIN RELIEF TO PROTECT THE ENTRY BLOCK WIRE CONNECTION. 

 Central Air Conditioning      Model: Air Handler, HB-D series 

 16

Содержание HB2400VD1M20



















Отзывы:

Нет отзывов