Haier HB2400VA1M20 Скачать руководство пользователя страница 2 | Manualshive

Страница: 2 / 15

background image

INDEX

TOPIC

PAGE

General
Physical dimensions
Replacement Parts Source
Installation Requirements
Air Flow Orientation
Horizontal Left-Hand Instructions
Downflow Instructions
Refrigerant Tubing
Condensate Removal
Electrical Connections
Thermostat Wiring
Orifice Change
Circulating Air Duct
Blower Performance
Start-up
Regular Maintenance
Model Number Explanation

The United States Environmental Protection Agency (EPA) has issued various regulations
regarding the introduction and disposal of refrigerants introduced into this unit.Failure to follow
these regulations may harm the environment and can lead to the imposition of substantial fines.
These regulations may vary due to the passage of new laws, it is recommended that any work
on this unit be done so by a certified technician. Should questions arise contact the local EPA
office.

THIS APPLIANCE IS NOT APPROVED FOR OUTDOOR INSTALLATION
THIS APPLIANCE IS NOT TO BE USED AS A CONSTRUCTION HEATER

GENERAL

This appliance was designed certified and must be installed in accordance with published
codes.In the absence of local codes please refer to the following codes:

NFPA 90A NFPA 90B
National Electrical Code NFPA 70
Uniform Mechanical Code

Prior to shipment, this appliance was tested and inspected for damage at the factory.Unpack
carefully and if damage is found, report it immediately to the transportation company.

This appliance is approved for installation in alcoves, basements, attics or crawlway, and is
designed for connection to air distribution ductwork.

2

2
3
4
4
5
6
7
8
8
9
10
12
12
13
14
14
15

«
1
2
3
4
...
»

Содержание HB2400VA1M20
















Отзывы:

Нет отзывов

Похожие инструкции для HB2400VA1M20

Бренд: York Страницы: 18

Бренд: York Страницы: 2

Бренд: York Страницы: 2

Бренд: Air Vent Страницы: 3

Lo-Carbon PoziDry Pro 476310

Бренд: Vent-Axia Страницы: 16

Бренд: Technibel Страницы: 6

Бренд: Reznor Страницы: 64

Бренд: Reznor Страницы: 76

Бренд: Mark Страницы: 88

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды