Haier GE CDT800P2N3S1 Скачать руководство пользователя страница 45

Страница: 45 / 80

– 45 –

Fault

Code

Load to Control

Timeout / Notes

F59

Dry Heater Thermistor Error - Out

of Range Low

Check that the thermistor harness is plugged in. Check

that the terminals are not bent inside the connector
housing.

F60

Heater Relay Stuck on Fault

Clear faults and cycle power to unit. If fault reoccurs

within 60 seconds of power up, replace MC board.

F61

CSM Check Failed

Cycle power and start cycle to clear fault. If fault does

not clear, replace main control.

F62

Dry Heater Fan Error

Check dry heater fan operation and verify speed is

greater than 2,500 RPM. Check that the dry heater fan
harness is plugged in.

F63

Flood Condition Fault

The pressure sensor has detected the water level

above the flood limit. Check the water valve for a stuck

open valve (continuous fill into the tub). Run the Fill

Test under the Diagnostics Test tab and ensure the

pressure sensor is in the range of 40.77 and 40.44 Hz.

Check that the fill funnel or door vent conduit at the

bottom of the door is not obstructed or blocked. This
can cause a pressure build up in the tub as the unit
heats during a cycle.

F64

Ignore Fault

Ignore fault.

F66

Dry Heater Thermal Cut Off (TCO)

Fault

Check harness. May need to replace the dry heater.

F86

No Fill Failure

Check the water valve; see if a water source is hooked

up to the dishwasher.

F87

Dry Heater Diagnostic Fault

Possibly any error with dry heater/relay/fan.

F96

Ignore Fault

Ignore fault.

F97

Absent Heat Source

Verify proper water level (no water will trip TCO).
Check heater TCO (replace TCO and harness if

tripped). Check heater. Check thermistor. Check main
control.

F98

Non-Draining Sump (Turbidity

Based)

Verify proper drain pump operation, restrictions and

installation.

F99

Minimum Wash Temp Not Met

Verify proper water level (no water will trip TCO).
Check heater TCO (replace TCO and harness if

tripped). Check heater. Check thermistor. Check main
control.

F112

Key Stuck

Pushbutton Models

: Check button operation, each

button should “click”. Check for plastic flash. Replace

user interface (UI) board.

Capacitive Touch Models:

Inactive F112's can indicate

inadvertent button contact, controls in Delay Start or

Control Lock mode, and consumer education. Check

that each key operates, each button should "beep"
and light up once pressed. If a key doesn't respond,
replace user interface (UI).

F128

Low Rinse Aid

Low rinse aid detected.

https://appliancetechmanuals.com

Содержание GE CDT800P2N3S1

















































































Результаты поиска

Содержание GE CDT800P2N3S1

Отзывы:

Похожие инструкции для GE CDT800P2N3S1

Бренды по названию

Популярные бренды

Haier GE CDT800P2N3S1, Техническое обслуживание руководство

Результаты поиска

Содержание GE CDT800P2N3S1

Отзывы:

Похожие инструкции для GE CDT800P2N3S1

Бренды по названию

Популярные бренды