Haier GE CDT800P2N3S1 Скачать руководство пользователя страница 20 | Manualshive

Страница: 20 / 80

background image

– 20 –

Tub and Structure

Ground Screws

Toe Kick

Insulation

Junction Box

Mounting Screw

Junction Box

The Tub and Structure section of this guide will

cover the toe kick, junction box, racks, leveling,
door balance, gaskets, trim (some models), main
control board, door, door components, as well
as the removing and separation of the screwless
appearance door. It will also cover the sump
module and removal. Details of the sump
components will be covered in the

Circulation

System

or

Drain System

sections of this guide.

Some models include tub trim, which clips to the

plastic tub to reduce sound levels and provides a
cleaner appearance to the installation.

If the cutout prevents the dishwasher from being
fully installed, or if the trim rolls inward preventing

the door from closing, it may be trimmed to

fit properly. The wiper edge must contact the

cabinet to be an effective sound barrier.

WARNING: GEA Factory Service Technicians

are REQUIRED to follow Lockout / Tagout

(LOTO) 6 Step Process prior to beginning

repair.

The toe kick panel is a safety and decorative

panel covering the machine area of the
dishwasher. The panel provides a safety barrier,
closing the front of the dishwasher machine
compartment. To remove the panel, remove two

1/4-in. hex-head screws and pull the panel away

from the dishwasher.

The junction box is located behind the toe kick

on the right-hand side of the dishwasher. The
junction box is where the 120 VAC house voltage
connects to the dishwasher. The dishwasher
may be hardwired, or an optional cord may
be installed (available separately,

Part #

:

WX09X70910), which plugs into a wall outlet

and connects to the harness plug into the control

(see the Installation Guide provided with the

appliance). The cover is held in place with a 1/4-
in. hex-head screw on the left side, and tab on
the right side. To remove the cover, remove the
screw and pull out and to the left to release the
tab. It is helpful to squeeze the top and bottom of
the box when removing and installing.

Tub Trim

Trim if needed

Insulation

Toe Kick

Toe Kick Screws

Tub Trim (Some Models)

Toe Kick

Junction Box and House Wiring

Connection

https://appliancetechmanuals.com

«
...
18
19
20
21
22
...
»

Содержание GE CDT800P2N3S1

















































































Отзывы:

Нет отзывов

Похожие инструкции для GE CDT800P2N3S1

Бренд: Belling Страницы: 18

Бренд: Gaggenau Страницы: 76

Бренд: Waterline Страницы: 31

Бренд: Euromaid Страницы: 33

Бренд: Logik Страницы: 108

Бренд: BALAY Страницы: 24

Бренд: Dometic Страницы: 32

Бренд: Bush Страницы: 44

Бренд: GE Страницы: 52

Бренд: TdA electronics Страницы: 12

Aquarius WDD 756

Бренд: Hotpoint Страницы: 16

Бренд: Samsung Страницы: 80

Бренд: Samsung Страницы: 44

Бренд: Samsung Страницы: 48

WA13J571 Series

Бренд: Samsung Страницы: 44

Бренд: Samsung Страницы: 14

Бренд: Samsung Страницы: 80

Бренд: Samsung Страницы: 56

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды