background image

– 49 –

Occupancy Sensors

 (optional)*

A wireless door sensor (located on guest entry door) and motion sensor (ceiling or wall 

mount) communicate to the Zoneline through a Setback Module.  The three components 

work collectively to determine whether the room is occupied or vacant.  When the guest room 

door is opened and motion is sensed, the MUAM will turn on and remain running (depending 

outdoor temperature and humidity).  When the door is opened again (the guest is exiting the 

room) and no motion is detected within five minutes, the MUAM will turn off.  If someone is in 

the room and motion is detected or the door is again opened the MUAM will cycle back on.

CDC (Central Desk Control)

 (optional)*

“The CDC input on Zoneline is an occupancy control option which is operated by the Property 

Management.  A field provided switch wired to the CDC connector can open/close the circuit to 

stop operation of the Zoneline when closed, and when open the Zoneline is operational.  The CDC 

connector can be used with an occupancy detection system to, instead, control the operation of the 

MUAM.  Such a system is optional and is enabled through the Aux menu.  It should be noted that if an 

occupancy detection system is enabled with a digital Make Up Air (*DBM and *EBM) Model, Central 

Desk Control cannot be used at the same time.

If the occupancy system is the suspect failure (confirm that Auxiliary Settings are turned on, see 

Auxiliary Controls

 section and 

Auxiliary Set Button

 section), the diagnosis can be verified by 

unplugging the CDC connector.  With the Zoneline turned off, the fans will be heard.  If the fans cannot 

be heard, enter Service Mode to turn the fan speed higher to verify operation.

*Occupancy Sensors and CDC are Optional accessories, only one may be used

Zoneline

Guest Door

Door Sensor

Motion Sensor

Wireless Signal

Wireless Signal

Содержание GE APPLIANCES AZ45E07DABW5




























































Отзывы: