Starting the Appliance
Starting a wash cycle
After having completed all of the installation steps in the preced-
ing paragraphs, turn on the water all the way and press the ON-
OFF button (A) located on the control pannel. The appliance is
on.
Cancelling or modifying a cycle
A cycle that is underway can only be modified if it has only been
running for a short time. Otherwise, the detergent may have al-
ready been used, and the appliance may have already drained
the wash water. If this is the case, the detergent dispenser must
be refilled (see the paragraph entitled, "Loading the Detergent").
To modify a cycle that is already underway, press the on-off
button (A), all of the settings will be cancelled. To set a new
cycle, follow the instructions contained in the paragraph entitled
"Setting and starting a wash cycle".
Setting the Wash Cycle with a Delayed Start Time
Button for "extra drying" or "half load" or "delay"
By pressing the "D" button in sequence ,the selection cursor (Q)
will come on in turn :
Extra drying -- Half load --Delay -- Extra Half load --Extra
Delay --Half load +Delay -- Extra Half load + Delay
Extra drying
By pressing the "D" button,the drying time of extra drying will be
longer ,and the drying relating is better.
Half load
By pressing the "D" button,this button (see "close-up View - Con-
trol Panel", letter "D") makes it possible to wash dishes using
only the upper rack if there are not enough dishes for a full load.
This will allow you to save on water and power. It can be used
before setting any of the wash cycle. Please keep in mind that
the amount of detergent should also be cut in half.
`óÅäÉ=éÜ~ëÉ=ìåÇÉêï~ó=áåÇáÅ~íáçå
`óÅäÉ=éÜ~ëÉ=ìåÇÉêï~ó=áåÇáÅ~íáçå
`óÅäÉ=éÜ~ëÉ=ìåÇÉêï~ó=áåÇáÅ~íáçå
`óÅäÉ=éÜ~ëÉ=ìåÇÉêï~ó=áåÇáÅ~íáçå
`óÅäÉ=éÜ~ëÉ=ìåÇÉêï~ó=áåÇáÅ~íáçå
The dishwasher is equipped an indicator "P" comprising 4 sym-
bols which represent the diferent phases of a wash cycle.When
the wash cycle has started,the display will indicate ,the phase
under way in sequence.There place are pre-wash,wash,rinse,
drying.
During the delay period, it is preferable not to change any of the
settings, If this is necessary, all of the settings must be cancelled
by pressing the ON/OFF button (A).
At this point, all of the steps for "setting the wash cycle with a
Delayed Start Time" and "Setting and Starting a wash cycle" must
be repeated, following the instructions contained in the corre-
sponding sections.
If the door is opened to the unit during the delay period, the count-
down will stop. It wil begin again when the door is closed.
All of the wash cycle set to reverse time function, we may in
focus start circulate time.
At the end of the wash cycle
Six beeps will indicate that the wash cycle has finished and the
LCD display (B) will come on (see fig.1). Turn off the appliance
using the ON-OFF button. Turn off the water supply to the appli-
ance and open the door. Wait a few minutes before unloading
the dishwasher to avoid handling the dishes and utensils while
they are still hot and more susceptible to breakage. They will
also dry better.
Setting and Starting a wash Cycle
Select the desired cycle by pressing programme selection but-
ton (F). Each time the button is pressed, the cursor"Q"will come
on in succession. Choose the wash cycle you feel is most ap-
propriate for the type of dishes that need washing (consult the
wash cycle table contained in this manual). After press the start-
pause button(E), the wash cycle has begun and can no longer
be changed. If necessary, read the paragraph entitled "Cancel-
ling or modifying a cycle"
Wash Cycle Program Light
The dishwasher is equipped with a program indicator (G) that
turns on when the appliance is running the wash cycle.
By pressing the "D" button (see close-up view-'Control Panel"),
select ,and the selection cursor turns on,then pressing the
"C" button ,the start of wash can be delayed for between 1 to 12
hours.
Each time the button is pressed, the display (M) will show the
number of hours for the delay period. Choose the amount of
time desired. After selecting the wash cycle, pressing the start-
pause button(E), the delay time on the display will blink.This in-
dicates that the countdown has begun.
After the time has elapsed, the cycle will start.
NOTE:
Wash Cycle adjustment Buttons
.6.
GB
pre-wash wash rinse drying
fig.1
