Haier AS12TB3HRA Скачать руководство пользователя

Страница: 36 / 58

Service diagnosis

Domestic air conditioner

10.3.5 IPM protection

Outdoor display: LED1  flash 2 times

Method of       IPM protection is detected by checking the compressor running condition and so on
Malfunction
Detection

Malfunction

■

The system leads to IPM protection due to over current

Decision

■

The compressor faulty leads to IPM protection

Conditions

■

circuit component of IPM is broken and led to IPM protection

Supposed

■

IPM protection dues to the compressor faulty

Causes

■

IPM protection dues to faulty PCB of IPM module

■

Compressor wiring disconnected

Troubleshooting * Caution Be sure to turn off power switch before connect or disconnect connector, or

else parts damage may be occurred.

Electrify the machine again and turn it on

with the remote controller,If malfunctions

are reported before or upon the compressor

being started up,

IPM Module is damaged and

needs replacing.

、

The system may have been over or under charged with gas, which can be judged through the pressure of the

measuring system.

、

The shaft of compressor is seized and the compressor needs replacing.

YES

The compressor is started normally, but

malfunctions are reported after it has run for some

time.

Malfunction unsolved

Содержание AS12TB3HRA



























































Результаты поиска

Содержание AS12TB3HRA

Отзывы:

Похожие инструкции для AS12TB3HRA

Бренды по названию

Популярные бренды

Haier AS12TB3HRA, Руководство по обслуживанию

Результаты поиска

Содержание AS12TB3HRA

Отзывы:

Похожие инструкции для AS12TB3HRA

Бренды по названию

Популярные бренды