background image

Followings are not problems

Sound of water flowing is
not a problem.

Sound of cracking is heard.

Smell are generated.

During operation, white fog or steam
comes out from the indoor unit.

No outlet air or fan speed can't be changed
in dry mode.

In cooling operation, unit switches to
blowing operation.

Won't start?

In heating operation, water or steam are
blown out of outdoor unit.

In heating operation, indoor fan won't stop
even if unit is stopped.

During unit operation or at stop, a swishing or
gurgling noise may be heard. This noise is generated
by refrigerant flowing in the system.

Unit will not restart after stop.

During unit operation, a cracking noise may be heard.
This noise is generated by the casing expanding or
shrinking because of temperature changes.

This is because the system circulates smells from the
interior air such as the smell of cigarettes or the
painting on the furniture.

When unit is running at places like restaurant, etc. where
dense edible oil fumes always exist, this will happen.

To prevent frost from accumulating on indoor heat
exchanger, unit will switch to blowing operation for a
while then resume cooling operation.

Though ON/OFF button is set
to ON, unit won't resume cooling,
dry or heating operation
in 3 min after it is stopped, this
is because of 3-min-delay
protection circuit.

Please wait 3 minutes

Unit will reduce fan speed repeatedly and automatically
if room temp. is too low in dry operation.

This occurs when frost accumulated on the outdoor
unit is removed.
(during defrosting operation)

After unit stop, indoor fan will go on running
until indoor unit cools down.

Trouble Shooting

20

Содержание AC142ACEAA


























Отзывы: