background image

148

 

The air conditioner should be effectively grounded. Electric shocks may occur if the air conditioner is ungrounded 

or inappropriately grounded. The wire for earthing shouldn't be connected to the connections on the gas pipe, 

water pipe, lightning rod or telephone.

 

The breaker for electricity leakage should be mounted. If not, accidents such as electric shocks may happen.

 

The installed air conditioner should be checked for electricity leakage by being powered.

 

If the ambient humidity bigger than 80%, when the water discharge hole be blocked or the filter becomes dirty, 

or airflow speed change, there maybe leads to condensing water drop down, and at the same time there maybe  

some drops of water spit out.

   CAUTION

 

It is not allowed to put any heating apparatus 

under the indoor units, for the heat may cause 

distortion of the units.

 

Pay attention to the aeration 

condition to avoid anoxic 

symptom.

 

Flammable apparatus should not be placed in the 

place where the air conditioner wind could reach 

directly, or incomplete burning of 

the apparatus may be caused.

 

Check the mount table of the 

air conditioner for damage for a long period of 

operation.

 

If placed on the damaged table, the unit may 

drop down causing damage.

 

Plants and animals should not be put to the place 

where wind of the air conditioner blows directly, 

otherwise damage to them may be caused.

 

It cannot be used for the preservation of food, 

living creature, precise instrument and artworks, 

etc, otherwise damage may occur.

 

Use the fuse with proper capacity. 

 

Metal wires and copper wires, etc., may 

cause fire or other faults.

 

Do not use water heater or like next to the indoor 

unit and the wired controller. Water/power 

leakage or short circuit may happen if the 

steam generating apparatus is working next to 

machine. 

 

Defrosting during heating

 

To improve the heating effect, the outdoor unit 

will perform defrosting automatically when frost 

appears on the outdoor unit during heating 

(approximately 2-10 min). During defrosting, the 

fan of the indoor unit runs at a low speed 

or stops while that of the outdoor unit stops 

running.

 

Do not touch the switch with the wet hand to avoid 

power shock.

 

Power should be cut off when the air conditioner 

is left unused for a long period. Power will be 

consumed if the air conditioner is not powered 

off. The power switch of the outdoor unit switch 

should be powered on 12 hours in advance before 

operation to protect the unit after a long period of 

storage.

 

3-minute protection

 

To protect the unit, compressor can be actuated 

with at least 3-minute delay after 

stopping.

 

Close the window to avoid outdoor 

air getting in.    

 

Curtains or window shutters can be put down 

to avoid the sunshine. 

 

Stop running and switch off the manual power 

switch when cleaning the unit.

 

During the operation of the control unit, don't 

switch off the manual power 

switch and the controller can 

be used. Please do not press 

the liquid crystal zone of 

controller to prevent damage.

 

Cleaning the unit with water may cause 

electric shock.

 

Do not put flammable spray close to the air 

conditioner.

 

Don't inject flammable spray towards the air 

conditioner, which may cause fire.

 

Stopping fan rotation

 

The unit which stops operating will actuate the 

fan for a 2-8 min swing every 30-60 minutes for 

protecting the unit while other indoor unit are in the 

operating state.

 

This appliance is not intended for use by persons 

(including children) with reduced physical, sensory 

or mental capabilities, or lack of experience 

and knowledge, unless they have been given 

supervision or instruction concerning use of the 

appliance by a person responsible for their safety. 

 Attention

Notices during Operation

Содержание AB052MCERA






























Отзывы: