Haier 1U50KEPFRA-H Скачать руководство пользователя страница 48

Страница: 48 / 71

Service Diagnosis

Check the indoor PCB: Only indoor

charged measure the voltage

between 3 and 4 of IC6 on the

indoor mainboard with a universal

meter. And measure the voltage

between CN23(S) and CN52 (L) with

a universal meter.

If the voltage is a constant value of

0V DC to 5V DC .Or the voltage

between communication line (red)

and N (white line) is not close

to18V DC when only indoor

charged.

YES

The indoor PCB is damaged; replace

it with a new one.

Test the outdoor power is

supply 230VAC with a

universal meter when indoor

and outdoor are charged.

Check the cable

between outdoor

and power

YES

Measure the voltage Between

3 and 4 of IC5 on the Outdoor

mainboard with a universal

meter. The voltage is a

constant value of 0V DC to 5V

LED2 light

The outdoor PCB is

damaged. Replace

it with a new one.

The outdoor PCB is

well, and then

check the cable

YES

Содержание 1U50KEPFRA-H








































































Результаты поиска

Содержание 1U50KEPFRA-H

Отзывы:

Похожие инструкции для 1U50KEPFRA-H

Бренды по названию

Популярные бренды

Haier 1U50KEPFRA-H, Руководство по обслуживанию

Результаты поиска

Содержание 1U50KEPFRA-H

Отзывы:

Похожие инструкции для 1U50KEPFRA-H

Бренды по названию

Популярные бренды