HAI 45A00-1 Скачать руководство пользователя страница 15

14 

HAI CONTROLLER INDICATIONS 

 
When the condition of a transmitter changes state, the HAI console will display that 
condition as follows: 
 

Transmitter Condition

 

HAI Console Display

 

When a transmitter (zone) is violated 

 

Zone Name "NOT RDY" 

When a cover is removed from a transmitter 

 

Zone Name "NOT RDY" 

When a supervisory failure is reported  

 

Zone Name "TRBL NOW"

When a battery low is reported  

 

Zone Name "HAD TRBL" 

 

 
FEDERAL COMMUNICATIONS COMMISSION (FCC) STATEMENT

 

 

This equipment has been tested to FCC requirements and has been found acceptable for use.  The FCC 
requires the following statement for your information:  This equipment generates and uses radio 
frequency energy and if not installed and used properly, that is, in strict accordance with the 
manufacturer's instructions, may cause interference to radio and television reception. It has been type 
tested and found to comply with the limits for a Class B computing device in accordance with the 
specifications in Part 15 of FCC Rules, which are designed to provide reasonable protection against 
such interference in a residential installation. However, there is no guarantee that interference will not 
occur in a particular installation.  If this equipment does cause interferences to radio or television 
reception, which can be determined by turning the equipment off and on, the user is encouraged to try 
to correct the interference by one or more of the following measures: 
 
• If using an indoor antenna, have a quality outdoor antenna installed. 
• Reorient the receiving antenna until interference is reduced or eliminated 
• Move the receiver away from the control/communicator. 
• Move the antenna leads away from any wire runs to the control/communicator. 
• Plug the control/communicator into a different outlet so that it and the receiver are on different branch 
circuits. 
 
If necessary, the user should consult the dealer or an experienced radio/television technician for 
additional suggestions.  The user or installer may find the following booklets prepared by the Federal 
Communications Commission helpful: “Interference Handbook”. This booklet is available from the 
U.S. Government Printing Office, Washington, DC 20402. The user shall not make any changes or 
modifications to the equipment unless authorized by the installation instructions or User’s Manual. 
Unauthorized changes or modifications could void the user’s authority to operate the equipment.

 

Содержание 45A00-1

















Отзывы: